Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Hollowing question

Posts

Hollowing question

#1

Hollowing question

Carole in VA

>Is it normal for the hollowing process to sometimes be VERY loud, or am I all of a sudden doing something wrong? This one small Box Elder vessel I am working on is driving me nuts...I need ear protection from the screeching! The tool (Stinger) seems to be cutting well, but good grief it's loud.

Re: Hollowing question

#2

Dick Hines

Re: Hollowing question

Dick Hines

>My Kelton rig gets right loud when hollowing dry wood. At presant I am working on a dry piece of big leaf maple burl and I don't think I will be doseing off while working on it.

Re: Hollowing question

#3

Re: Hollowing question

Ed Karch in No.VA

>I have had a couple of hollows scream me deaf.

Re: Hollowing question

#4

Ric Taylor

Re: Hollowing question

Ric Taylor

>I remember that during my first hollowing project, while being bombarded with lots of noise, I kept thinking, "This is supposed to be fun...."

Re: Hollowing question

#5

Dick Hines

Re: Hollowing question

Dick Hines

>If you think about it when you a hollowing out a iece of wood you are making a loud speaker. The noise is amplafied inside the walls of the form. And you are scraping and not as getting a clean cut as when you are using a skew or gouge.

It's kind of like singing in the shower,LOUD, and your singing is proubley good anyway

Re: Hollowing question

#6

Re: Hollowing question

Bill Grumbine (Kutztown PA)

>Hi Carole

Call me a sissy pants, but I clap on my hearing protectors when I get out the hollowing tools. Of course, if you persist long enough, the noise won't seem so bothersome. ;-)

Bill

Re: Hollowing question

#7

Thanks!

Carole in VA

>I'm glad it's normal. Sometimes I wonder if the thing is not getting ready to explode on me! LOL The worse the grain the louder the noise, I guess. Dick has a good point about a hollow vessel acting as a sort of loud speaker.

Re: Hollowing question

#8

Re: Hollowing question

Mark Kauder, Phenix City, AL

>Carol,

I know you don't need to spend any more money, but a bowl steady (which you can make for $20) will cut down on the noise by dampening the vibrations.

Mark

Re: Hollowing question

#9

Leave it to a woman...

Jay in TX

>to ask the questions I never thought of. I just thought the screeching was normal (or that I was doing it wrong and didn't want to admit it!)

Re: Hollowing question

#10

I have posed this same exact question

Mike Schwing from Md.

>But at the time nobody answered that they also have the same problem. Quite a different response this time!

I do as Bill G. indicates - I put on my Ruger shooter's earmuffs.

Re: Hollowing question

#11

Sheepish grin here

Carole in VA

>I have a Oneway Bowl Steady that has not been taken out of the box yet. I fifured I didn't need it for a little 6" bowl.

Re: Hollowing question

#12

Re: Leave it to a woman...

Carole in VA

>LOL My teachers in school used to just sigh because I was always asking questions. But I hate to think of the things I wouldn't have learned over the years if I had not asked. Most nights the last thought in my head before falling asleep seems to be "I wonder why xxxx" about something or other.

Re: Hollowing question

#13

Re: Hollowing question

Russ Fairfield

>Spray a little water on the wood, just enough to dampen the surface, and the noise will be less.

Re: Hollowing question

#14

Re: Sheepish grin here

Mark Kauder, Phenix City, AL

>Shame on you - a tool you own and have not used!! Well, I never....well actually I have.

You will find that placing the bowl steady opposite where your tool pressure is (backside of the lathe if cutting on the outside, frontside if cutting on the inside) will cut the noise/vibration. HOWEVER, with hollowing, I really like a fully captured vessel. As such, I have two Oneway Bowl steadys that I stack so that I have one on each side, capturing the piece. I think you will find that you can cut more aggressively, safely, when you have the bowl captured. I just bought the two Oneways, rather than make a new one for my Vega (already made one for my Jet Mini, because it was cheaper than buying a ready-made one and I did not have the time to make my own.

Mark

Re: Hollowing question

#15

Re: Making your own *LINK*

Russ Fairfield

>It isn't that difficult to make your own bowl steady. The link shows how I did it, and saved a couple hundred.


Make a Bowl Steady

Re: Hollowing question

#16

Brad Vietje

Re: Hollowing question

Brad Vietje

>Carole,

I'm a little surprised that Boxelder is loud -- I usually have the loudest noises with real hard woods -- Black Locust is the worst.

A smaller radius tip may cut with less noise.

Safe Spinning,

Brad Vietje

Thetford, VT

Re: Hollowing question

#17

Re: Leave it to a woman...

Bill Crommett

>Carole: That charteristic is also known as "Nosiness". and I have been one of the nosiest people to own a lathe.

Always learning:

Bill