Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Cutting Timbers Question

Posts

Cutting Timbers Question

#1

Cutting Timbers Question

George Van in WI

>I am going to cut some platter and bowl timbers to dry for later use from spalted logs (maple, yellow & white birch). If I do not do this they will rot. I will use my Woodmiser to cut these and plan to sticker them outside for a year before moving to the pole building, top of pile covered, to dry. I will end coat with Anchorseal but I am not planning to coat the top and bottom unless recommended. They will start their drying cycle in the slow drying months which if they act as lumber should minimize defects? Pith areas will go to the woodpile for next years heat.

Questions I have are recommended thickness for platters? Will bowl and hollow form blanks be too thick for this method and have to be further reduced and sealed all around to reduce checking? I am sure I am not the first to try this and I hope to benefit from the experience of others.

Re: Cutting Timbers Question

#2

Re: Cutting Timbers Question

Mike Schwing from Md.

>Personally, 1-1.25" is plenty thick for me to work a platter. I simply epoxy a glue block onto the blank for the chuck and have the full thickness for working the platter.

Drying thicker bowl blanks will, in my limited experience, be less successful, even heavily stickered and weighted. Even your best efforts will still leave them moist enough inside to warrant the normal roughing/drying methods most of use with our bowl blanks.

Re: Cutting Timbers Question

#3

Re: Cutting Timbers Question

Greg in Oshkosh

>It's been my experience with spalted maple that as the spalt proceeds the tendency for the wood to split decreases. The decay releases tension in the wood. So I don't have to do too much to prevent checking on thicker blanks. Once they are in plank form, I have had little degrade.

My best method with all woods for 8x8 is to wax the ends. I use an electric fry pan, put the wood into the hot wax and let the wax soak into the endgrain for a few minutes. Better luck than using endseal.

Re: Cutting Timbers Question

#4

Re: Cutting Timbers Question

Barbara Gill, Remlik VA

>I have been cutting bowl stock on my WoodMizer for several years now. I have cut some thick (4") planks but you can pretty well count on cracks forming somewhere. I have had better luck with using the sawmill to cut the thickness (removing the pith) then cutting the planks into correct lengths with my chainsaw. For really large 5"-8" thick and 16"+ in diameter I coat end grain at least 2 times and rest at least 1 time with AnchorSeal. Then I either use or sell them as soon as possible. Smaller blanks get the same AnchorSeal treatment then are stickered inside an old horse stall to keep. If they sit around too long, they will crack and eventually become firewood. It is best to either use or sell as soon as possible.

I use 4/4 and 5/4 stock for plates and platters. This is cut into boards, stickered and allowed to dry before turning. I like to air dry at least 3 years before using.

Re: Cutting Timbers Question

#5

Re: Cutting Timbers Question

George Van in WI

>Thanks Mike, I like the idea of the glue block, not wasting the wood for a foot. If I had to rough later it would still be better than loosing the logs to rot. It seems my method will still have problems from drying checks in the large dimentions.

Re: Cutting Timbers Question

#6

Re: Cutting Timbers Question

George Van in WI

>Thanks Greg, I too though that because the white rot fungus feeds on lignum, the wood would be more forgiving. I will try a couple of timbers for a control. If a problem they will still be good for boxes!

One of the turners from Appleton that moved up here also uses your fry pan sealer.

Re: Cutting Timbers Question

#7

Re: Cutting Timbers Question

George Van in WI

>Thanks Barb, you definitely have the experience with several years of trial. Other than a few controls left full length just “to see”, I will follow your method. I have been able to keep blanks fully sealed for two summers in my shed without cracking.

In our area 4/4 and 5/4 will be 11-12% MC at the end of August if stickered in the winter and covered with a roof. Do you find the MC lower after 3 years or are you allowing movement to settle? I bring my wood in the shop, maintained at 38% RH and sticker to lower further. I check my lumber and blanks with the Wagner electronic meter.

Re: Cutting Timbers Question

#8

Re: Cutting Timbers Question

Sean Troy

>Hey George, what model Wood Mizer do you have? Sean

Re: Cutting Timbers Question

#9

Re: Cutting Timbers Question

Barbara Gill, Remlik VA

>I like the flat stock to have a number of seasons to move. In general the MC here in Virginia will be between 12-14%. The only way other than using a kiln is to sticker under a tin roof with good circulation. Even with wood dried to around 9-10% I like to give it several seasons of movement before using it. I have been told that the old woodworkers would not use wood that was less than 7 years old.

Re: Cutting Timbers Question

#10

Re: Cutting Timbers Question

George Van in WI

>Hi Sean, I have a LT40HD, it has been a good machine!

Re: Cutting Timbers Question

#11

Re: Cutting Timbers Question

George Van in WI

>Thanks Barbara, I would agree that the surprises may be minimized over the years, and here I though all that lumber was stored in the building because I didn't have time to use it, now I know I have been planning!

Re: Cutting Timbers Question

#12

Re: Cutting Timbers Question

Sean Troy

>Thanks George, I'll be looking to purchase one when we move next summer.

Re: Cutting Timbers Question

#13

Re: Cutting Timbers Question

Greg in Oshkosh

>I got the idea from Ron Warshall whom I beleive you are referring to.

Re: Cutting Timbers Question

#14

Exactly

George Van in WI

>