Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Drying Conditions For Blanks?

Posts

Drying Conditions For Blanks?

#1

Drying Conditions For Blanks?

Thomas Skaggs, Foothills of Mount Level

>Hi Folks,

A fellow called me the other night and offered me a large cherry tree. He just cut it down last week and said I can have the trunk. I suppose there is a potential for a good size pile of large rough blanks.

In the past I have stacked wood chunks in the garage (after sealing). But I will have a tougher time finding room for much more wood.

What about sealing the stuff, then stacking it on supports (not touching the soil) and covering with a tarp?

What are the desirable conditions for storing wood chunks?

Tommy

Re: Drying Conditions For Blanks?

#2

Re: Drying Conditions For Blanks?

Greg in Oshkosh

>I have had good luck putting the untreated blanks in plastic garbage bags and loosely sealing the opening. The danger is that trapping all that moisture will cause fungus to grow. Here in WI the temps are dropping and soon the moisture will be quite solid. I have kept blanks this way for two years in the garage. Another outside storage technique I have used is to put the blanks in a 5' plastic swimming pool. The kind used for kids that are made of rigid plastic. I then cover the blanks with sawdust generated from cutting them up and leave it out in the rain. The pool fills with water keeping the blanks wet and yet there is so much that rot does not occur.

I have left this pool of blanks out over the winter with good results.

Note that during the winter it is difficult to extract a frozen in ice blank for indoor use.

Basically any technique will work that controls the moisture loss.

The Italians used to keep logs under water so they wouldn't check before they got around to using them.

Re: Drying Conditions For Blanks?

#3

Out of sun and wind.

Dave Smith, Longview, WA

>Hi Tommy,

I have a lot of blanks in various places. The two most important things are sun and wind. The sun will cause uneven drying thus cracking. The wind will cause excessive drying on the exterior and even more cracking than the sun. These are observations on my part with no scientific study to back up my claims. I like to sticker the blanks to insure even air flow and to reduce fungus growth from excessive moisture accmulation when wet blanks are stacked in a mass heap.

Have you considered having some of the trunk cut into lumber?

Dave Smith

More wood than room in Longview, WA.

Re: Drying Conditions For Blanks?

#4

Re: Out of sun and wind.

Thomas Skaggs, Foothills of Mount Level

>I thought about flat stock Dave but I so rarely get my hands on sizable cherry for turning that this seemed to be a good opportunity to stock up. Besides, I'm pondering where I can pile some turning stock already. Room for stacking and stickering lumber is even more of a challenge!

Thanks for the info buddy.

Tommy

Re: Drying Conditions For Blanks?

#5

Re: Drying Conditions For Blanks?

George Van in WI

>Tom, I have some blanks that have been Anchorsealed and left on pallets, covered with a tarp and they are still good without end checking for two summers and a winter (up here it is covered with snow for 4-5 months). I have not seen any mold but I think the tarps keep the moisture a little higher. I have yellow birch, maple, and some cherry. Most have been cut in half but some full round pieces are still ok.

Re: Drying Conditions For Blanks?

#6

What I would do...

KurtK in Indy

>Hey Tommy,

Nice score....I would probably buck the trunk into logs that are as long as round.I think the biggest issue you would have would be end checking. I would then coat the ends of those babies with anchorseal and then stack them like firewood (with the bark still on them) Get 'em up off the ground and I think you probably wouldn't need to cover them. They should keep and then when you're ready, grab one and cut it up into several blanks and use whatever you will and seal the others.

Sounds reasonable to me?!?!

I'm pretty lucky...I've got that 5K whse that I can load all of my stuff into. BTW....got a hold of some interesting wood couple weeks ago. Make sure you call me whenever you run through Indy...I'm sure something would find its way into your trunk.

Have a good one,

Kurt

Re: Drying Conditions For Blanks?

#7

Re: Drying Conditions For Blanks?

CapeMayMike

>I have a lean-to type structure, open on three sides that I built next to my shop and store my wood there on pallets. Before that I stored wood on pallets covered with a tarp but somewhat open on the four sides to allow air to circulate. I usually try to cut out the pith, seal and stack. When I don't remove the pith, I still use anchorseal but I leave the log as long as possible to allow for loss. Cherry is notorious for cracking and checking. I'd get rid of the pith and seal, better yet I'd try and rough as much as possible. I'd also do my best to protect the wood from constant wind which can cause rapid drying, cracking and checking. Pallest along a wall that protects from prevailing wind would help, then a tarp to cover.