Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

For the accident archives

Posts

For the accident archives

#1

For the accident archives

CapeMayMike

>As Ray Barrone's father would say...."Holy Crap Marie!".

I'm a fairly safe woodworker. I've had accidents but they've always been minor nicks and scrapes. The worst was the time I drove a screw through two boards and then into my hand with a screw gun, pretty dumb but fortunately not too severe of an injury. My relatively good safety record came to a screeching halt today and thanks to whoever it is that looks after meatheads I avoided the severe injury that could have been a result of my lapse at the lathe.

I was sanding a pepper mill which was held in an Axminster chuck, using a strip of 240 grit like a shoeshine rag, on my 3 hp Vicmarc. I was wearing a very loose fitting pocket style tee shirt. I rarely wear pocket shirts when on the lathe for the obvious reason, I don't want a pocket full of shavings. I'm leaning into and over the work and in a split second I'm violently yanked into the lathe. I weigh 275 lbs so it takes a bit of power to yank me violently. I instinctively pull back while my tee shirt is torn completely from my body, turning me 360 degrees, wrapping about the chuck.

This entire fiasco occurred in less than 5 seconds. After an inspection to insure that all limbs and digits were still intact and functioning properly I found that I had a large abrasion on my left side upper abdomen, where it impacted the chuck and a second less severe one on my right side.

I unwound the shredded and twisted tee shirt from the chuck. Apparently, while leaning over the work, the chuck caught the pocket and the lively dance insued. The shirt is a sight to behold. Both arms are torn open, as is the neck down to the waist. It has the appearance of one narrow long rag.

I'm going to hang the shirt from the shop ceiling as a reminder to me and I thought I'd post this as a reminder to everyone else that shop accidents do indeed occur in the manner as everyone who's experienced them describes, blindingly quick and when least expected. I was lucky that all I suffered was a bruised belly and ego.

Be safe!

Re: For the accident archives

#2

Re: For the accident archives

Sean Troy

>Keep an eye on the injury to make sure no internal damage happened. Glad to see your ok.

Re: For the accident archives

#3

Re: For the accident archives

Ronny Eelen (from Belgium)

>That's scary!

It does make you think when reading this.

Re: For the accident archives

#4

Re: For the accident archives

John Lucas

>Wow that's scary. I worry about my clothing because I like loose shirts. I'll try to watch closer.

Re: For the accident archives

#5

Re: For the accident archives

Pete in Holland, MI

>As I tell kids who start using the tools in my shop: The quicker a hand tool or machine can do an operation to a piece of material, the quicker and more suvere an injury can occur.

Play safe everyone !

Re: For the accident archives

#6

When a vivid imagination is a bad thing ...

John Trant (Baltimore/DC corridor)

>Hi Mike,

I am sorry to hear about your misfortune but am glad that nothing significant is injured (however, your T-shirt may beg to differ).

For those that have never met Mike in person, he is indeed a large man in both muscle mass and height (i.e., twice my size). The reason I tell you this is so that you can appreciate the picture in my mind's eye of "Big Mike" doing a quick pirouette in front of his lathe while he is being disrobed like a $2 Chippendale dancer.

Now I have to go and kill myself to get that picture out of my head!

;-)

Again, I am glad you are OK.

John

Re: For the accident archives

#7

Re: When a vivid imagination is a bad thing ...

JamieDonaldson

>At least you won't need any implants to restore your profile!! Glad you dodged the bullet!!

Re: For the accident archives

#8

Thanks for posting the warning!

Bill Howatt

>

Re: For the accident archives

#9

Re: For the accident archives

Ron Parsons SE NM

>No kidding, I just saw a rerun of Home Improvement and Tim Allen was standing in front of the lathe discussing not wearing loose cloths around a lathe. About that time the shirt was ripped off him. At least he had a tear away shirt.

Re: For the accident archives

#10

Re: When a vivid imagination is a bad thing ...

woodspinner/ Bill Hale

>John I love the picture you painted.

Most of all glad he is OK.

Bill in Casa Grande, AZ.

Re: For the accident archives

#11

Re: For the accident archives

Ron in Drums PA

>Boy!

I'm glad you you are alright.

Reminds me back when I was in high school. A kid in my shop class had his long hair get caught in a drill press. I won't describe the gory mess, but I'll say he didn't have long hair after that.

Re: For the accident archives

#12

Steven Antonucci

You are a sick dude! LOL

steve antonucci

>Never met Mike, and I'm certainly glad he's OK, but my first instinct was that in retrospect, it would have probably been funny as all hell to witness (minus the obvious seriousness of the situation.)

Then I read your post, and I snorted! At least I am not the only one who's reaction was to giggle at Mike description...

Glad you're ok. 3HP is probably enough to spin Mike, if the chuck got a hold of him. I've spun 110# on my 1.5HP Nova...

Steve

Re: For the accident archives

#13

Re: For the accident archives

AndiWolfe

>I'm glad you're ok after that accident, and thanks for posting the reminder. I always remove my watch and ring before using the lathe, but I don't often think about pockets on my shirt being a hazard, too.

Re: For the accident archives

#14

Re: When a vivid imagination is a bad thing ...

CapeMayMike

>Hi John,

First and only pirouette that I've ever done and first time that I've been compared to a Chippendale....$2 or otherwise. You may require an exorcism to remove the "dancing bear" image from your tortured psyche!

Big and bruised Mike.........

Re: For the accident archives

#15

Re: For the accident archives

Carole in VA

>Holy smoke, Mike! You are one lucky dude! You may have saved my butt though...I realize now that I have been rather lax in paying attention to both what type of shirt I wear when turning as well as how close it is coming to the chuck. This is particularly a problem in the winter when I have long sleeves. :( Glad you are ok except for some scrapes and bruises.

Re: For the accident archives

#16

Re: For the accident archives

CapeMayMike

>Hi Sean,

Fortunately, well sort of, the impact was overtop of my lower ribs and they absorbed it. Abrasions and a nasty bruise but that's it.

Re: For the accident archives

#17

Re: For the accident archives

CapeMayMike

>Hi Andi,

After the incident and my original post, I grabbed my surf rod and headed to the beach, needless to say I was done for the day as far as the shop was concerned. While wading about and tossing a plug I rflected on the incident. The loose shirt and pocket contributed, however the biggest contributory factor was my position. Thinking back on it I realized that I had been standing near the headstock and then leaning toward and over the work, placing that dangling pocket right into the path of the chuck. Why I was in that position I'm not sure but I think it was a bit of laziness. I remember that I was resting my left forearm on the top of the headstock, sort of leaning on it. I should have been over toward the tailstock with only my hands out over the work. The loose shirt contributed a bit, but it was primarily user error, I placed myself in a bad position. Bet I don't do that again!

Re: For the accident archives

#18

Re: For the accident archives

CapeMayMike

>Thanks Carole,

See my reply to Andi.

Mike

Re: For the accident archives

#19

Re: For the accident archives

JKJ in East TN

>Thanks for sharing that.

During cave diving training we were required to study case histories of cave diving fatatalities. When I got my tractor I read every thing I could find on ways to get killed with a tractor. (Not many people just get hurt in a tractor accident. I have a list if anyone wants it.) And in fourth grade I sat beside a boy who had just two fingers on one hand and three on the other after "playing" with his dad's table saw - that made a huge impression on me. I think each accident we hear about makes us all a little safer.

Something that scares me at the lathe that I see too often, even in demos, is someone holding a sizeable cotten cloth against a turning. I read somewhere about such a cloth getting caught and removing a part of a finger. I do use cotton cloth for friction polish on small spindles (I don't like the paper towels) but I use pieces about 1" square. I've never once thought about loose pockets.

My woodworking contribution: don't grip the wood with a finger just behind where the drill bit will exit the wood. Duh. Years ago I drilled right through my nail and part half way through my finger with a 1/8" bit. The only thing I remember hurting more and taking longer to heal was a stingray hit to a finger while scuba diving in the FL keys.

JKJ

Re: For the accident archives

#20

Thanks...

Jack Savona

>...for the reminder that we ALWAYS need complete concentration at the lathe. It is a tool that could be fatal if not totally respected.

So glad you're able to tell about it. Sorry you had to.

Re: For the accident archives

#21

Keith Tompkins

Re: Thanks for posting the warning!

Keith Tompkins

>Glad you are ok, Mike!

Re: For the accident archives

#22

Oh dear!

Carole in VA

>There have been times when I have leaned my left arm on the headstock to do something...don't ask me what 'cause I can't remember. Whatever it was, if I need to do it again, I bet I find a different way!

Re: For the accident archives

#23

Something else I need to watch

Carole in VA

>I just realized tonight that when I put on another pair of glasses I have in the shop, I often forget to remove my regular glasses which hang on a cord around my neck. The thought of having my head snatched down into a spinning chuck should prevent me from doing THAT again!

Re: For the accident archives

#24

Re: For the accident archives

Pat Mulligan

>Thanks for posting this,Mike.Glad you didn't get seriously hurt.

Re: For the accident archives

#25

What should we learn from this?

Ed Moore

>Mike,

I'm glad that the damage was no worse than what you have described.

There is a clear message to all this: Remove rings, watches, glasses on cord, smocks, and shirts before turning. Haircuts should be military in style.

Imagine the new turning tee shirts: "TURN NAKED".

Now try NOT to think of all the members of this group as they obey the rules above - it could be harmful to your mental health. But I bet it could evoke a grin or two. ;^)

Ed

(PS: For the humor-impaired, this was intended as a joke.)