Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Reverse Chucking-for Derek

Posts

Reverse Chucking-for Derek

#1

Reverse Chucking-for Derek

Jennifer@Indy.USA

>Derek posted a question about reverse chucking a bowl the other day and I searched the archives for a thread that was sometime in the past but couldn't find it. Someone posted that he used PVC pipe fittings to create a reverse chuck and I thought it was a fantastic idea and tried it myself and rarely use any other method now. The advantage of the PVC fittings are that they come in various sizes, it is quick and easy and allows the bowl to stand out beyond the headstock which comes in handy for reversing natural edge bowls. One thing I am very careful of is not to over do it when expanding the jaws inside the fitting. I'm sure if you cranked hard enough it could possibly fracture and cause a not so pleasant experience. Prior to using the fittings I round over the edges and remove anything on the pipe that might interfere with the adhesion of the anti slip material. I use a rubber, adhesive backed product to keep from marring the surface of the bowl and to alleviate any slippage. I'm sure you could find any number of materials from mousepads to FunFoam in the craft section of any hoby store. Also the antislip stuff for shelving in the kitchen isle is a good one. I pull the tailstock up and all it takes is a slight bit of pressure to keep the bowl in place. I don't use the point in my live center so I won't have a divot to carve away later. Especially if I'm not removing a lot of thickness off the foot. I'll only have a tiny nib to remove.



I have made two of the donut things for different sized bowls and for me it was a complete pain. Very cumbersome and aggravating. I can't get the feel for how the form is flowing into the foot with the donut. Some would argue that a vacuum chuck is the way to go for reversing and I agree I would love to have one but have just never gotten around to putting one together. With this PVC method I do have to remove a small nib when I'm done with the foot, but in all honestly, taking the bowl over to my bench and sitting there with it and carving off the nub with a Flexcut fishtail chisel is part of the process that I really enjoy. It's here when I put the last few cuts into a bowl and then sand the bottom to it's final finish and then sign my name. I really do love that part of it.

Anyway....just my way, and thoughts on reversing a bowl for finishing the foot.

Jennifer

Re: Reverse Chucking-for Derek

#2

Re: Reverse Chucking-for Derek

Barry Irby

>Someone about a month or two ago posted about six different ways of doing this (John Lucas maybe?). One that amazed me was using blue masking tape and not a lot of it. I would have used several rolls, but they uses about two or three wraps. That series of posts should have been made into an article.

I have used the PVC fittings also and am also leery of cracking them. I think in compression they are fine, but if you are expanding into them, be very careful. I use cheap carpet pad for friction surface and don't bother to attach it. Each time I use the piece of pipe or fitting, I tend to true up the end just to be sure and then I just put the pad over the end and hold it on with the bowl while I bring up the tail stock.

I cut the nib off with a thin pull saw or a knife or chisel and sometimes I use my drill press to sand the bottom. I just chuck in a small sanding disk and set the bowl face down on the table and bring the disk down to it.

On Natural edge bowls or bowls that have warped while drying I shim them level and then sand the bottom flat so they will sit flat when turn upright.

Re: Reverse Chucking-for Derek

#3

Re: Reverse Chucking-for Derek

Derek

>Thanks for your idea Jennifer I am going to definitely make an appointment to make one of those. Or two as Barry has.

I also agree with Barry that "You" or some one else should do an article on holding a bowl to finish the bottom as there isn't one.

Derek

Re: Reverse Chucking-for Derek

#4

Re: Reverse Chucking-for Derek

Ian

>As a plumber for over 20 years I can understand your thinking about cracking the pvc. With that said, plumbing supply houses carry schedule 80 pvc, thicker and denser than the usual schedule 40 we all know and love. Another thought would be to put a worm clamp around the the pvc where it mounts into the jaws.

IAN

Re: Reverse Chucking-for Derek

#5

Re: Safer PVC chucks

JamieDonaldson

>Jennifer et al- rather than using chuck jaws to hold the pipe sections, turn a hardwood plug which can be fit inside one end and fastened with several flat head screws countersunk for safety. Then true up wood/PVC face and drill hole for screw chuck- works well and no danger of splitting the pipe. I have also made similar chucks for a variety of uses by sawing slots in the front opening and holding wood in place by clamping with a band clamp. But put tape over the clamp tightener screw to reduce chance of whacking a knuckle! Blood doesn't always make an attractive stain pattern on a turning!

Re: Reverse Chucking-for Derek

#6

Re: Reverse Chucking-Question?

Turner

>Jennifer,

How are you sealing the chuck to maintain vacuum?

Re: Reverse Chucking-for Derek

#7

Re: Safer PVC chucks

Carole in VA

>OK, I know this is a dumb question, but what tool do you use to "turn" the edges of the PVC true? I figured I would use a gouge just like I do to shape the edges of bowls, but that's definitley not working very well! (PVC=1, CBV=0) On the next piece maybe I should try a scraper?

Re: Reverse Chucking-for Derek

#8

Re: Safer PVC chucks

JamieDonaldson

>Carole- a bowl gouge worked for me, but turn down the RPM's-too fast gets a little grabby!

Re: Reverse Chucking-for Derek

#9

She doesn't...

Jay in TX

>Turner,

Jen is using this as a type of friction chuck, very ingeniously I might add.

Jay in Saginaw, contemplating the eve of 31 years on this planet and still dropping the IQ level of many rooms I enter.

Re: Reverse Chucking-for Derek

#10

Re: She doesn't...

Turner

>Jay--

Assumptions can make a guy feel pretty dumb sometimes. Thank you for correcting mine!

--Turner