Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

roughing gouge questions

Posts

roughing gouge questions

#1

roughing gouge questions

Georg Waldhof

>Just bought an actual roughing gouge. Am now discovering it works a bit differently than spindle gouges. So, now I have questions:

What bevel does anyone prefer for these? The one I bought is a P&N and I made my own handle for it. The bevel is fairly steep and I feel like I'm letting the wood pound itself off rather than cutting. Am I holding it wrong?

I'm betting someone is going to tell me to have a live instructor show me the ropes on this one ;-). Good advice if I can get access to such an instructor. Short of that, what are some of the recommended books on chisels, techniques and sharpening?

Thanks

G

Re: roughing gouge questions

#2

Re: roughing gouge questions

Jim Shaver - Oakville, Ontario

>Hi,

I use a roughing gouge with the tool rest higher than for my other work. I use it only in spindle turning.

I like to introduce the edge of the gouge at a high angle and not straight on, riding the bevel, usually skewed with an edge down and with a light touch to take off the high points. As the edges become homogenous and the wood becomes a continous surface I switch to a spindle gouge or skew.

Not sure if that helps.

Take care,

Jim

Re: roughing gouge questions

#3

Re: roughing gouge questions

Sean Troy

>You are only using it for rounding square stock?

Re: roughing gouge questions

#4

Re: roughing gouge questions

adrien

>It has a coarse, 45° angle. start at one end, taking off an inch or so at a time. A turner named Jack de Vos from down under uses it not only for rough shaping, but like a skew. "peeling" cut is at 90° to the piece, "shearing" cut is with gouge 45° on the tool rest. It's a wonderful tool for removing lots of wood very fast.

Re: roughing gouge questions

#5

Keith Tompkins

Re: roughing gouge questions

Keith Tompkins

>Hi Georg, keep in mind that the roughing gouge is a spindle turning tool, not a bowl turning tool. I don't use the roughing gouge in a back and forth motion like most turners, instead, staying in one spot, I remove wood til smooth. Then start a new cut...cut move over, cut move over. That way I take less of a beating from the tool. Fast too!

Re: roughing gouge questions

#6

JL

Re: roughing gouge questions

JL

>I have two roughing gouges (smaller and somewhat larger). I typically have the tool rest down below center a bit with the handle on my body. I ride the bevel better that way.

Re: roughing gouge questions

#7

Re: roughing gouge questions

John Lucas

>Keith I thought I was the only one using a roughing gouge that way. I push the gouge in and let it naturally move in the direction of the flute. Usually to the right because that throws the shavings away from me. I make a series of pushes to go from square to round and the move the gouge across that area to smoothe it up.

I sharpen my rough out gouge to a more acute angle that most people because I will use it not only to make the wood round but to rough shape almost all the details. I use the "wings like a skew so I have a left hand skew and a right hand skew. I leave the are at the top of the U 90 degrees to the straight wings so I can use this area in a peeling but to quickly remove wood close to a detail like a bead.

This allows me to almost completely turn a spindle before I even pick up another tools. This not only lessens the number of times I have to sharpen the other tools but speeds up the use. For example on my mirror handles I may only need one or two passes with the skew to finish up the handle.

Re: roughing gouge questions

#8

Keith Tompkins

Re: roughing gouge questions

Keith Tompkins

>Great minds think alike, John! He He

Re: roughing gouge questions

#9

Re: roughing gouge questions

Rick Allen

>Hi Georg

With the roughing gouge straight on lower the handle so that only the heel of the bevel is rubing.

Now slowly raise the handle until the cutting edge starts to remove wood.

Move the tool left and right.

You will find you need to raise the handle a little to keep cutting.

Do NOT round over the corners of the gouge. You can use those corners to get into some tight spots.

Good Luck

Richard

Re: roughing gouge questions

#10

THANKS to all - extremely helpful!!!

Georg Waldhof

>