Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Vacuum pump location?

Posts

Vacuum pump location?

#1

Vacuum pump location?

Colin Spencer

>I have just bought a Gast 0523 vacuum pump. This has a fan on the rear of the pump for cooling. I have read articles here and on the web as well as in Woodturning design about Vacumm chucking but the pump location gets little mention. Where do I mount the pump to keep the dust out of the fan housing? How much airflow is ith likely to need? Can anyone help or is this a Gast question.

TIA

Colin

Re: Vacuum pump location?

#2

Re: Vacuum pump location?

Jim Pugh, Ohio

>I initially had mine on the floor at the back of the lathe but it kept being covered by chips so now it is on a high shelf with a cardboard box over it to keep the dust off. The box isn't a close fit, just a 'roof' that collects loose dust. This has worked well for me for about 18 months now.

Re: Vacuum pump location?

#3

Re: Vacuum pump location?

Bob Hackett

>One of the best tips I`ve seen was to mount the pump on plywood attached to the rails of a light weight handtruck,keeping it up and out of the dust/shavings.This had the advantage of giving you a place to mount the valve,filter,etc at a nice height and accessable just about anywhere the hose will reach. It also provides a place to hang the power cord and the hose and rotary connection when not in use.The whole thing wheels around(obviously) and stores out of the way in a corner.

Mainely,Bob

Re: Vacuum pump location?

#4

Far away...

Peter Teubel

>A friend of mine has his pump mounted in his attic over the shop. Hard wired to a wall switch and a coiled air hose coming down from the ceiling. I will be doing the same.

Re: Vacuum pump location?

#5

Re: Vacuum pump location?

vicmarc.fan

>I have had one of these on the floor behind my lathe for over two years. The vacuum part is mounted on the front of the motor and the air intake cools both motor and vacuum pump. The vacuum pump is totally sealed once a connection is made. I do have a filter in the vacuum side in case the chuck or something is dirty. On the side of the motor is note on a solution you can run through the vacuum part. I have never done this. Frankly for what I paid for this at Omaha Surplus I can replace it three times for what the one Craft Supplies costs. I know this is not the point but I use my pump almost daily and have had no problems with it uncovered on the floor. I just blow it out when it gets too dirty behind the lathe. I think I did this once last year when I gave a demo. to the club. Did you know you can use the output side as a compressor. I sometimes use it for my airbrush.

Ron

Re: Vacuum pump location?

#6

Re: Vacuum pump location? *LINK*

Mark Kauder, Phenix City, AL

>You can see my pump in my review of the Vega 2400 (the blue thing on the headstock end of the lathe. It adds ballast to my lathe, and is out of the way. It is also out of the direct line of fire for dust and chips. I periodically blow it off with compressed air and have not had a problem with it for the two plus years I have had it. Before it was on this lathe, it was in about the same location on the stand for my Jet Mini.

Mark


http://www.woodcentral.com/cgi-bin/readarticle.pl?dir=reviews&file=articles_503.shtml

Re: Vacuum pump location?

#7

Re: Far away...

Don Evans

>How HOT does that attic get during summer?

Something to consider. Also, attic's can be really dust bins depending on the venting etc.

It may not be the best environment for your pumps health.

Also, can you hear it? If it quits you want enough time to duck.

Don

Re: Vacuum pump location?

#8

Re: Not too far away...

Bill Turpin in WNC mountains

>Vacumm pumping capacity is inversely proportional to the square of the distance or orifice. If you make the hose twice as long, you will net one fourth the cfm. Make it four times as long = one sixteenth! The smallest orifice in the set-up is the determining factor. Go from 3/8 to 1/4 orifice or hose and speed will be less than 45% of 3/8.

Bill in WNC mountains

Re: Vacuum pump location?

#9

Re: Vacuum pump location?

Jim Ketron

>Here is my set up


img

Re: Vacuum pump location?

#10

Re: Vacuum pump location?

Colin Spencer

>Thanks for the input everyone.