Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

bottle stoppers

Posts

bottle stoppers

#1

bottle stoppers

Laff in OKC

>I'm trying to turn bottle stoppers drilled for a 3/8 dowel. I cut the dowel long enough to glue in, leave room for a cork, and enough to be held in a Jacob's drill chuck. I realize that my touch is still very heavy, but I'm tired of twisting off the dowel. Does anyone have an idea for a mandrel or jig to help with this?

Re: bottle stoppers

#2

Re: bottle stoppers

Dick Parr

>This is the one I use on my Jet mini to make stoppers.

http://www.pennstateind.com/store/pk-bs1-mj.html

You can use the drill that comes with it, but I use the next size down so it is a tighter fit. If you are making the chrome stopper you just screw it onto the turning when you are done, but if you are using a dowel with a cork stopper then just drill the hole out to 3/8" and glue your dowel in.

Works great for me.

Good luck

Dick in Knoxville

Re: bottle stoppers

#3

Ric Taylor

Re: bottle stoppers

Ric Taylor

>Laff,

I just use a 3/8" bolt with the head cut off mounted in a chuck as a mandrel to hold the blank for turning and finishing.

Ric

Re: bottle stoppers

#4

Re: bottle stoppers

Robert Savit

>If you're not doing it already, try bringing up the tailstock for support. Wait until your final cuts to finish off the tailstock end, which you will do lightly, after retracting the tailstock. You can be pretty aggressive with the tailstock in position and not twist off the dowl.

Bob Savit

Re: bottle stoppers

#5

Re: bottle stoppers

Bruce Wiseman

>Mount a fairly long (3 or 4 inch) peice of wood on to your face plate. Turn it round. Use the jacobs chuck in the tail stock to drill a 3/8 hole into the wood. remove the wood from the lathe and take to the bandsaw (or hand Cut) two right angle relief cuts through the drilled hole. Put the thing back on the lathe. Slide your wood dowel into the opening and use a small hose clamp across the relief cuts to tighten the wood around the dowel. BE CAREFUL of the clamp when the wood is turning it can be a knucle buster! THe further you put the dowel in the more support. Trade off is being able to get at the bottom on the stopper. Once you've made one you can experiment with the shape to get something that works well for you.

Re: bottle stoppers

#6

Re: bottle stoppers

Jerry Whitaker

>I turned a piece of stock to about 2 1/2 inches in diameter and about 1 1/2 inches thick and tapered slightly towards the tailstock end. Put a 3/8 bit in chuck and drilled all the way through the center. Then I marked where the piece goes in relationship to the #1 jaw so it can be placed in the chuck in the same place each time. Removed the piece, laid headstock end down and cut a slit from the outside to the center of the 3/8 in. hole and about 1/2 in. beyond to the opposite side on the bandsaw. The slot to the outside removes enough wood so that the chuck will clamp down on the dowel and hold it tight and the 1/2 in. cut on the other side of the hole gives it enough "spring" to hod the dowel tightly and also to remove it easily. Hope this all makes sense. Sorry, don't have working digital camera to take a picture.

Re: bottle stoppers

#7

Re: bottle stoppers

Lee Dale

>When you bring tail stock up for support, place a fauchet washer between the live center and the blank. Saves cutting off the marks from the live center....Lee

Re: bottle stoppers

#8

Re: bottle stoppers

Jim Pugh, Ohio

>You have a lot of possibilities already given but Ric gets my vote. You can also use a 3/8" metal dowel (get from machinist supply) and glue the wood dowel in when you are fininshed turning.

Wooden dowels have very little strength in torsion (twist) and the drill chuck jaws don't help the problem because they are relatively sharp and cut into the dowel in 3 places making it weaker yet.

You can hold the metal dowel in your drill chuck, your lathe chuck or glue it into a face plate mounted block altho in that case drill a hole thru everything so you can knock the dowel out later if you so choose.

Re: bottle stoppers

#9

Re: bottle stoppers *LINK*

Ed Davidson (Colorado Springs)

>Here's a link to a little tutorial that may help...


Cork bottle stopper making

Re: bottle stoppers

#10

Re: bottle stoppers *LINK*

Ed Davidson (Colorado Springs)

>And here's another tutorial link, focusing on stopper chucking and holding methods...

best regards,

Ed D.


Stopper mounting tutorial

Re: bottle stoppers

#11

Re: bottle stoppers

Laff in OKC

>Thanks to all for your responses. There are several here that I will try.