Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Anybody got an old Rockwell lathe?

Posts

Anybody got an old Rockwell lathe?

#1

Anybody got an old Rockwell lathe?

Gary Evans Tallassee, TN

>I acquired an old lathe today from my friend Dick Parr. I think it is an old Rockwell, but the only decal on it refers to the brand of the bearings in the headstock. Had I been smart, I would have taken some pictures to post here so that someone could tell me what it is.

Having failed that, and not having the lathe close at hand until next week, I wonder if someone could post a picture of their old Rockwell or other brand so that I can try to determine what this one actually is. It has a 12" swing and about 40" of length. The headstock has, I think, a 3 step pulley on it. Correct me if I'm wrong, Dick.

Links to pictures of old lathes would also be appreciated.

Thanks for any help,

Gary

Re: Anybody got an old Rockwell lathe?

#2

Re: Anybody got an old Rockwell lathe?

Lester Gillett Independence Mo

>I have one for sale in the classifieds and a picture of it you might

look at.

Lester

Re: Anybody got an old Rockwell lathe?

#3

Re: Anybody got an old Rockwell lathe?

Gary Evans Tallassee, TN

>Hi Lester,

I looked at that picture the other day, but this is a different model. It is not variable speed. It has a step pulley in the headstock and no metal stand. Dick had it mounted on a heavy-duty homemade stand.

I may have to go down where I have it stored and take some pictures. Just trying to avoid burning the gas.

Thanks,

Gary

Re: Anybody got an old Rockwell lathe?

#4

Re: Anybody got an old Rockwell lathe?

Dick Parr

>Gary I sent you an email with some more pictures of it, but here is one of them.

It does have a 4 step pulley on the head and that is a heavy duty 3/4 hp motor I put on it.


img

Re: Anybody got an old Rockwell lathe?

#5

Brad Vietje

Re: Anybody got an old Rockwell lathe?

Brad Vietje

>Sure looks like my dad's old Rockwell to me. His was a slightly newer-looking model from about 1958; I'm guessing yours is in the '50 -'52 range, no ? BTW, if you use it a lot for larger bowls, you'll probably get better performance (less vibration) with a beefier toolrest banjo. My dad had his welded a few times before he had a heavy duty one made by a local machinist. I think off-the-shelf banjos for certain models will work fine, but I don't remember which. Delta offers a more rugged banjo, but the bed gap wasn't right -- If you measure the gap, I may have just the thing you need ...

Safe spinning,

Brad Vietje

Thetford, VT

Re: Anybody got an old Rockwell lathe?

#6

Re: Anybody got an old Rockwell lathe?

Wayne Leach

>Hi Gary,

This is my Rockwell 3400 which is around 40 years old! Apparently, according to some it is much sought after (although I don't know why)?

The wooden knobs on the banjo etc are my own creative touch!

Hope this helps?

Wayne in NW Ontario and winters in Eufaula, Alabama


img

Re: Anybody got an old Rockwell lathe?

#8

Re: Anybody got an old Rockwell lathe?

JanManuel

>My Rockwell lathe is a little bit heftier than that one. It has a 4-step pulley, the left side of the stand where the motor is, has a sheet metal housing. Right side is open, with a shelf. I long ago stacked 7 concrete blocks there for ballast.

I don't know how old it is. I bought it in 1985. I have no idea how many thousands of hours I've used that lathe, it still gets turned on most every day. I have a bigger DL40 lathe I do most of my turning on, but I run sanding drums and stuff in the "little" lathe. If I'm turning tiny things, I prefer the little lathe..highest RPM is faster and the headstock is smaller, and less in my way....

Re: Anybody got an old Rockwell lathe?

#9

Re: Anybody got an old Rockwell lathe?

Gary Evans Tallassee, TN

>Thanks for the offer of a beefier banjo, Brad, but in addition to the original Dick gave me one that looks suspiciously like the Jet 1236 banjos that I just bought the other week. I am looking for the guts for a 1236 banjo if you have them. I have a housing without the internals.

Unfortunately, I don't think that I'm going to have an opportunity to turn on this old boy. It's going with me to GA this weekend to try to sell at the Turning Southern Style symposium.

Thanks again,

Gary

Re: Anybody got an old Rockwell lathe?

#10

Re: Anybody got an old Rockwell lathe?

Gary Evans Tallassee, TN

>Thanks everybody for your help. I got this lathe for re-sale and wanted to make sure what it is that I'm selling.

Looks like it is a late '40's to early '50's model. Hopefully I can find it a good home this weekend at the GA symposium.

Thanks again,

Gary