Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

moving

Posts

moving

#1

moving

Joe Herrmann

>I've just sold my home and am planning to move my tools and other equipment into an unheated, unfinished shop I started some time back. We will eventually be building a house on that same property. The winters here in NE Ohio can be brutal and I am concerned with rusting.

What would be the best way to store the tools. Should I coat the exposed metal parts with some kind of a rust inhibitor, should I cover them with blankets, or should I just let them "weather" without any protection.

Joe

I am looking to use them periodically so I really don't want to smear some kind of goop all over them that would require removing prior to use. I assume, therefore, that some kind of covering would be best. Any suggestions??

Re: moving

#2

Re: moving

Jim Shaver, Oakville, Ontario

>Hi Joe,

I do not heat my shop in the winter and I have a ritual that seems to work.

I move all the small things like hand tools, etc into the house and keep them in a heated space.

I dispose of all finishes and glue that I can not trust to survive a freeze thaw cycle.

I clean and remove any accumulated saw dust from my shop that might trap moisture, also at the same time I lubricate moving parts on my table saw, jointer, planer etc with the right kind of lub as recommended by the many sources out there. I also pull all my blades and knives out and send them out for sharpening. In the spring I tune each machine and set the newly sharpened cutters.

I then spray down my machined surfaces with a commercial coating (Bostik Top Coat) meant to keep the top lubricated and slipper during actual use. I take old bed sheets and drap them over the tops to keep them dry and allow air circulation

I have been doing this now for eight years, the only casualty in this process has been the tyres on my bandsaw, for some reason they split and crack after a number of these cycles.

take care,

Jim

Re: moving

#3

Re: moving

John Lucas

>Joe I used to use Johnson's floor wax on all my table surfaces and then try to wipe off all the dust off of other parts. I've had a somewhat heated shop ever since.

Re: moving

#4

Heh, heh...I had a solution, but then...

Rod Peterson -- Ormond Beach

>Jim,

When I first read that your tyres [sic] split I immediately thought of replacing them with hockey pucks. Surely you have some of those laying around. Then I realized you were talking about the tires on the blade wheels and not on the mobile base (assuming you have a mobile base). It's still not a bad idea, but it doesn't solve your problem. Sorry.

Rod

Re: moving

#5

Re: moving

Bruce in Saint John N.B. Canada

>Joe just take an clean rag (terry cloth works nice)and soak it with automotive lubricating oil SAE 30 is ideal. Then wipe over all the ferreous metal surfaces you want to protect, leave a good film of oil this will prevent any rust from forming. The beauty of it is that it is easy to remove in the spring or during the cold weather if a need arises to use any of the tools, one just has to wipe the oil off with a clean dry rag. If you oil machine table tops and you are not satisfied with the clean dry rag routeen you can always apply a little varsol on the rag and there won't be a trace of the oil remaining on the said object. By the way stay clear of and rubber parts as oil will act on most rubber by swelling and cracking it. Thats why someone else metioned that he had to replace his bandsaw tires every few years. Like John was saying wax also works well and many people use it with great luck. A friend of mine used it one winter on his 8" jointer and come the spring he didn't get it thoroughly removed and it contaminated some cherry lumber thus affecting the finish he applied. Hope this helps, good luck with your move.

Bruce in Saint John, N.B.

Re: moving

#6

Re: moving

Kevin Turner

>Joe. Winters aren't winters til you live with the bears...LOL. If you southern folk use skidoos' check out the storage spray they use for the engine block. This stuff goes on kind of foamy/ oil type residue. Blankets may hold the dampness. Cheers KevinT

Re: moving

#7

Re: moving

Tim Grenville-Cleave

>We don't have winters here in the UK just rain! and for most thats enough.

I was shown a method years ago by an old guy in a machine shop who used a heavy cotton/calico type cloth cut into pieces large enough to cover each machine, first he would lay out the cloth and spray a good coat of a water resistant fluid all over it (something like WD40, also used to coat auto electrics and drive out moisture etc) then spray the machine as well, with lathes do not forget M Tapers,(Including all electrics and switch gear). Cover the machine with the cloth sprayed side down!!.

If you need to be use it, a quick wipe down of the ways or the tables and away you go.

Advantages of this method are:- spray offers protection of electrics, cover not only keeps moisture at bay but dust as well!! Easy to recommission as needed.

I have used this method for several years with no upsets in a very damp shed.

Tim.

ps not trying to teach granny to suck eggs!!

Re: moving

#8

Re: moving

Roy Girolami

>Joe, here in NC we don't have really cold winters but we do have very humid springs and summers. My shop is in a barn, totally unheated and with a concrete floor that I don't think has a vapor barrier in it. I tried the oil on the tables, the top-cote, the vapor barriers on the machines. The only thing I found to stop rust is to cut a piece of plywood and put it on the machine table. All the small hand tools do just fine if kept in a cabinet. I have use all my tools year round and don't find any problems except when I forget to replace the plywood.

Roy Girolami

Apex, NC

Re: moving

#9

Re: moving

Joe Herrmann

>Thanks guys for all the suggestions. I'll ponder them and and hopefully will choose the right one. Fortunately I'll be close enough to check periodically and will be able to offset any damage before it gets too bad.

Joe