Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

jet mini saga

Posts

jet mini saga

#1

jet mini saga

John Lucas

>As some of you might remember I bought 2 return item jet mini lathes from a local supplier. They seemed to work OK but had no torque on the motor. I finally had time to check them out yesterday in the electronics lab at work. Apparently the Power supplies are OK and the motors are bad. We hooked the motors up to completely different DC supply and they still don't have any torque. New motors are $197 so that's out. I already have one of the Vega DC motors and will set up one lathe with that. Now I'm looking for another motor. Does anyone know of a source for used or cheap motors that I can put on the other lathe. The ideal thing of course would be a DC motor that would be the same size as the Jet. I've lost the address of the surplus place that sells motors. Does anyone have that?

Re: jet mini saga

#2

Re: jet mini saga *LINK*

Gary Evans Tallassee, TN

>Hey John,

How about www.surpluscenter.com?

Gary


Surplus Motors

Re: jet mini saga

#3

Re: jet mini saga

John Lucas

>Thanks Gary, that's the place I used to look at, I was just having a senior moment.

Re: jet mini saga

#4

What is the voltage of the motor ? .

Fred in NC

>

Re: jet mini saga

#5

Re: What is the voltage of the motor ? .

John Lucas

>Fred The motor says 162vdc on the label.

Re: jet mini saga

#6

Then .....

Fred in NC

>To figure out what motor to use, we need to know the output voltage from the controller at the maximum speed setting.

If one takes 120 V AC and rectifies with a full bridge, the DC voltage output will be ... you guessed, about 160 volts! So maybe that is what the controller is doing, and then ramping it down for slower speeds.

However, (I don't have the VS model, I use a Vega motor) this is only a guess, and the motor could well be overrated, or even used with a lower voltage.

Surplus Center has permanent magnet DC motors in 130 and 230 volts, from $10 to $30 depending on the motor. These are surplus treadmill motors, and are very good.

Using a 230 V motor with a lower voltage will both reduce the speed and torque, but it will be at least 1/2 HP so it should work with the Jet Mini.

They also have a nice Minarik controller for about $60, which will work with the 130 V motor.

Hope this helps.

Re: jet mini saga

#7

Re: Then .....

John Lucas

>Fred I will check the voltage this weekend. I think it ran from about 60 to 130vdc or so but I don't remember exactly. I looked on the surplus website but all the motors I found were $60 to $120. I'll have to look again. Anyway I will look at the specs on the motor to see what speed,etc, and check the output voltage.

Re: jet mini saga

#8

Try this... *LINK*

Fred in NC

>Surplus Center has two different versions of a 130V motor, here is one: http://www.surpluscenter.com/item.asp?UID=2005090816452082&item=10-1783-A&catname=electric


130 V Motor

Re: jet mini saga

#9

Re: Try this...

woodspinner/ Bill Hale

>If you use this type motor be sure to add a fan to it. They do not have the pulley on it and it has the fan in it.

These work great. They also have the controllers.

Good company.

Good turning and be safe

Bill in Casa Grande

Re: jet mini saga

#10

Re: Try this...

John Lucas

>Fred I checked the motor this morning. It is 162v 3 amp 1800 rpm motor.

Re: jet mini saga

#11

are these the same?

Dennis Taylor

>John, does the motor to the older mini, not variable speed use the same motor as the variable speed?...Dennis