Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Pyrography Machine Workshop

Posts

Pyrography Machine Workshop

#1

Pyrography Machine Workshop

Ben Aragon

>Pyrography Workshop

I gave a demonstration in February on how to build a pyrography machine using a PC power supply to my local woodturning club. The machine was based on a design from Pascal Oudet. We at the New Mexico Woodturners Association had a pyrography workshop on Sept. 3rd and 4th. The pyrography workshop was very successful, after a lot of hard work from everyone the machines are finished. We were able to build 16 machines. I would like to thank everyone that came and helped at the workshop. I would especially like to show appreciation to Ken Pilkington and Ron Phillips for providing most of the power supplies, and thankfully we had extras to work with. I have a very special thank you to my lovely wife Peggy who acted as hostess and photographer thank you for providing the refreshments. A lot of fun was had by all. I would lastly like to thank Pascal Oudet for a great design.

Best Regards,

Ben


img

Re: Pyrography Machine Workshop

#2

Workshop members

Ben Aragon

>Some of the workshop members.

L to R, David Brahinsky, Ken Pilkington, Ben Aragon, Ron Phillips, John Ellis, Jerry Trujillo, Janet Smith.


img

Re: Pyrography Machine Workshop

#3

Workshop members

Ben Aragon

>hard at work


img

Re: Pyrography Machine Workshop

#4

Re: Pyrography Machine Workshop

Peter Toch

>Hi Ben:

Your post on making pyrography machines looks very interesting. There are several members in our woodturner's group that would be interested in building these for their own use. Could you supply me with more details? Parts list and sources, wiring diagrams, schematics, and any other information you have would be greatly appreciated.

Thanks, Peter Toch

Re: Pyrography Machine Workshop

#5

Re: Workshop members

John Lucas

>I think the wax will work. I have used a candle to wax my screw center when feeding it in really hard wood.

I use a homemade pin chuck for my wine stoppers but then I use dowels and corks. I am planning on using Ruth's new stoppers if I ever get around to ordering them. Maybe this will remind me to send her a check today. If I'm not a master at procrastinating I must have at least a Brown belt in the art.

Re: Pyrography Machine Workshop

#6

wrong message-must be early

John Lucas

>

Re: Pyrography Machine Workshop

#7

Link to Pascal`s design?

Bob Hackett

>

Re: Pyrography Machine Workshop

#8

Re: Link to Pascal`s design? *LINK*

Ben Aragon

>Here is Pascal Oudet's website.

http://www.freehomepages.com/aurepascal//tournage/pyrograveur_eng.htm


Pascal Oudet

Re: Pyrography Machine Workshop

#9

Re: Link to Pascal`s design?

John K Jordan

>Clever use of the computer PS. I can't remember how many of these I've ripped apart just to salvage the fans. It looks like you found plenty of room inside the box for the components. I suspect many people would like to build one of these. It might be a great project for turning clubs all over.

Did you use the circuit exactly as Pascal indicated, make mods, or use a different circuit? What mosfet did you use for Q1? Did you have to adjust the frequency from the 555?

Care to share some notes?

JKJ in East TN

Re: Pyrography Machine Workshop

#10

Re: Pyrography Machine Workshop

chris rolke

>interested in this

must not be awake because i am not seeing how to totally do this

any more info?

thanks

Re: Pyrography Machine Workshop

#11

Parts List

Ben Aragon

>Here is a Parts list and wirng diagram.

Part # Decription quantity

Newark Elect http://www.newark.com/

06H2924 5 ohm 25 watt resistor 1

06H2916 10 ohm 25 watt resistor 1

01F8239 1 k ohm Pot 10 turn 1

01E9279 22 uF Capacitor 1

18C4834 10 nF Capacitor 1

29C4871 1N4148 diode 1

06F7573 ICM7555 Timer Chip 1

25C3677 8 pin DIP socket 1

27C6760 IRF3708nMOSFET 1

93F3488 12V pannel lamp 1

89C9912 switch DPST 1

02J8380 RCA jack for pen 1

84N1165 RCA jack for machine 1

66F9795 RCA plug for cable 2

12B7437 50 ohm resistor 1

12-611 DATAK protoboard 1.7"x2.9" 12-611 1

NiChrome wire 18 Gauge http://www.morelectric.com/nichrome.htm

Can't find source anymore Pen tubes Phenolic 3/8 ID , 1/2 OD 1

Monster speaker wire Wire 14 gauge 3ft I used Monster wire 1

for the pen cable.

Homemade brass connector for Nichrome wire 2

1/8 dia. 1/2" long, 18 gauge & 14 gauge holes

in each end. Silver soldered


img

Re: Pyrography Machine Workshop

#12

Proto board layout

Ben Aragon

>I used a proto board Datak 12-611 for the circuit you have to build. The MOSFET is a switch that turn ON and OFF current to the pen to control the temperature. The MOSFET is controlled by the 555 timer circuit. Look at Pacals website for a better description. Some PS need load resistors to turn ON some don’t.

Good Luck,

Ben


img

Re: Pyrography Machine Workshop

#13

Thanks Ben

Bob Hackett

>

Re: Pyrography Machine Workshop

#14

excellent - pic??

John K Jordan

>Ben,

Thanks for the details.

I notice the image suffered a bit from the JPG compression such that some of the smaller text is difficult to read. Do you possibly have a higher resolution version? If so and you want to email it to me, I'd be glad to try processing it for better readability and repost. (I have some tools and had good luck with this on similar graphics.)

JKJ in East TN

Re: Pyrography Machine Workshop

#15

Re: excellent - pic??

Ben Aragon

>John,

I will email the photos to you maybe you can repost them.

Thanks,

Ben

Re: Pyrography Machine Workshop

#16

repost of circuit diagram

John K Jordan

>Ben,

I redid some text to hopefully make it easier to read. The proto board diagram is already easy to read. I hope I didn't introduce any errors! I did notice a few minor inconsistencies between the proto board, circuit diagram, and parts list you gave earlier:

PROTO BOARD:

- 12V line from PS is not shown connected to trace on board.

- The "to pen" label shows two connection dots, shorted. (other side of pen should go to ground/common)

- Load resistor is not shown connected, but I assume that's since it's not always needed.

COMPONENTS:

- Parts list indicates 10 ohm resistor, diagram shows 12 ohm. (either should work)

- Parts list does not include heat sink for mosfet. (diagram specifies a heatsink)

- Parts list indicates DPST switch, diagram shows SPST switch.

Thanks again. I'm going to try to build one of these when I get time and show it to our club. It should go together pretty quickly, even for those without much experience. How long did you allow for your workshop? Was everyone experienced with soldering? Did you have a Weller for each person? (I have two or three here.) Perhaps each person could wire and stuff and a couple of experienced people could come around and help with the soldering if necessary. Did you take a scope for testing? Any problems, hints?

JKJ in East TN


img

Re: Pyrography Machine Workshop

#17

Re: repost of circuit diagram

Pascal Oudet

>John,

the 2 points which are important are

- about the 555 circuit: must not be a NE555, which has a too low max supply voltage value. TLC555 (or I suppose ICM555 as Ben used, I haven't checked) have a higher max value. they are powered by the 12V supply, which could move a bit upwards and reach the max rating of circuit)

- the mosfet: this is the most critical point. use a mosfet with as low as possible a RDSon if you can't find the one used by Ben.

otherwise you might be able to do pyrography with the mosfet itself ;-) (some failures to make this circuit work have been reported in the past and it was due to a wrong mosfet)

Pascal

Re: Pyrography Machine Workshop

#18

Some More Instruction

Ben Aragon

>Some More Instructions

John,

Here are some modifications and tips that I hope will help.

1. Who ever is in charge of the work shop needs to have electronics back ground either a technician or engineer. There is dangerous high current inside these PS.

2. I soldered up all the boards days before the workshop, it was a lot of work but I’m glad I did. It is a delicate job working with that Datak proto board. At the work shop it was difficult for some to solder the switch without melting it, it’s not their fault. From start to final test on each proto board it took about 45 minutes. Yes check each board with an oscilloscope.

3. Open the PS look to see where you can mount the switch, pot, RCA jack, lamp, and board. I mounted the board on the fan of the PS, I’ll post a photo later. Remove the PS’s main board, blow out the dust and drill your holes. Remount the PS’s board.

4. Cut the connectors off all the wires and separate them by color.

5. Mount and connect the 12v lamp to a yellow and black wire. Mount the RCA jack and pot.

6. Use a PS that has an ON/OFF switch. Cut the old switch off and solder the wires to the new switch and mount the switch. (Switch, blue to white and brown to black.) Test PS, see if it turns on, if not add load resistors. If it still doesn’t turn on scrap it. We mounted the load resistors under the cover.

7. I used a 10 turn pot instead of a 1 turn pot. The 1 turn pot came to full power at ¼ turn the 10 turn pot came to full power at 2-1/2 turns, better dynamic range.

8. I didn’t use a heat sink on the MOSFET, it is rated for 60 amps and I think at most this pen is pulling 3 amps.

9. Connect 12V and 5 V lines to the proto board and MOSFET and mount it some where in the PS. Connect the MOSTFET to the RCA jack and the proto board to the pot.

10. Turn the pot fully CCW, connect the pen and test the PS.

Skill levels of our participants varied but all were mechanically experienced and everything got done.

The pen building is another project altogether.

Look at this website for a start on instruction,

http://www.fishcarver.com/making_fish_scale_tips.htm

And

http://www.fishcarver.com/images/burning%20instructions.PDF

Or buy pens already made I really like this guy’s pens. We built ours like these where the tips are silver soldered to the pen for a much better connection.

http://www.carvertools.com/frmain.htm

I scheduled the work shop for one Saturday day. It took me all day Thursday to make 16 proto boards. Friday I finished them and proto typed the pen design easy day. Saturday 10 people attended the work shop and we built most of the 16 PS, all the pens and pen cables. Sunday 4 people returned and we finished the PS and we had 12 working units at days end. The rest of the week M-F I repaired 3 of the 4 that didn’t work and had to completely build a new 4th.

Have fun and my Best Wishes,

Ben

PS email me if you have questions I’m sure it’s clear as mud and I may have forgotten a few things.

Re: Pyrography Machine Workshop

#19

Re: Some More Instruction

John K Jordan

>>2. I soldered up all the boards days before the workshop,

That's the biggest thing I wondered about - an inexperienced person is unlikely to make good solder joints. (I got my practice in the mid '70s soldering up boards and peripherials for my 6800 computer - a single 8K (not 8meg!) memory board was $250 as a kit and had 1434 solder connections, all of which needed to be perfect.) Actually, it wouldn't be too hard to design and etch a few boards just for this circuit - the board could be very small. I made many of these in my home-brew computer days. In that decade rolling your own was the only way to get some functions into your computer (such as a time-of-day clock or bitmaped graphics output).

The project looks simple enough. Perhaps the mosfet could be bolted to the inside of the case as a heatsink if it gets hot, with an isolating insulator if necessary. I might suggest purchasing a ready-made pen.

Thanks again for your time on this. I'm adding all of this info to my files.

JKJ in East TN