Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Toolrest height continued

Posts

Toolrest height continued

#1

Toolrest height continued

Mike Schwing from Md.

>I was turning a bowl this afternoon and thought it represented a good opportunity to show my tool rest height for exterior work and tool presentation. Sorry Russ, I did not fuss over the pic. (wink)

On the lathe is a pretty large, very figured silver maple bowl with grain changes every 1/8" or so throughout. Silver maple is prone to tearout on its own, figured is doubly so.

You can see in the photo that my highly polished toolrest is set as low as it will go, easily 2" below centerline. The round, well maintained, ding free rest allows for continuous, finish quality turning that no dinged up rest ever could. I take a drywall screen and drag it back and forth on my rest every few minutes to keep it this way. I find it well worth it and the drywall screens last a long time.

The tool presentation is ala "Terry Daniels style". Tool handle held low against my hip, flutes pointing mostly back at me, one bevel rubibng the work and the cutting edge just barely making contact at one point. The cutting edge is making contact about 1/2" below centerline. This gives a flawless cut and with practice makes for a surface better than a lot of folks achieve through sanding. You can see the surface of that bowl as it exists presently needs nearly no sanding at all, but I will still start at 180 grit, or lower if it was needed. If near the rim of the bowl, where grain change takes place, the bowl starts to chatter, I reverse my handhold and pull from the other direction.

Astute observers will also notice the flutes are pretty bright - I usually hone the cutting edge on a leather wheel before making final finishing cuts. MOST of the time it improves cut quality.

Hope that helps someone! Try it, you'll like it!


img

Re: Toolrest height continued

#2

Re: Toolrest height continued

Ron in Drums PA

>Try some wax on your tool rest Mike.

Re: Toolrest height continued

#3

Re: Toolrest height continued

Jorge Castaneda

>Mike,

A picture is worth a thousand words, and your picture tells the story perfectly, thanks for posting it, now I have to try it. Your finish looks great the way it is. I will also adopt your shiny tool rest and honing the bevel as well.

Thanks very much for sharing,

HJorge

Re: Toolrest height continued

#4

Re: Toolrest height continued

Mike Schwing from Md.

>Thanks Ron. Jorge, glad I was of some help!

Ron, I've tried various waxes and polishes on the toolrest but don't prefer them. They seem to invariably gum up either the rest or the tool for me. What exactly are you using?

Re: Toolrest height continued

#5

Re: Toolrest height continued *LINK*

John K Jordan

>I use Renaissance wax on my cast iron tool rest, bandsaw table, etc. I haven't noticed any gumming or residue.

The hype says it is "microcrystalline wax polish", but I have no idea what that means.

JKJ in East TN


Renaissance wax

Re: Toolrest height continued

#6

Re: Toolrest height continued

Chris Wright

>This is a great cut for sure Mike, one thing to note is it does translate to spindle gouges as well. Tool presentation is slightly different, but once you know how to find the 'sweet' spot, you can do this with pretty much any winged gouge and make very nice finishing cuts.

Re: Toolrest height continued

#7

Re: Toolrest height continued

JamieDonaldson

>Hey Mikey- nice photo, but about that blue shirt!! It turned your hand blue!!!LOL,LOL

Re: Toolrest height continued

#8

Get ready to laugh

Mike Schwing from Md.

>That shirt was white!

Re: Toolrest height continued

#9

Re: Toolrest height continued

Ron In Drums PA

>I use a candle

Re: Toolrest height continued

#10

Re: Toolrest height continued

Ed in No.VA

>Gee Mike I thought we were going to get to see your armpit stance.:o)

Ed