Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

A few recent turnings...

Posts

A few recent turnings...

#1

A few recent turnings...

Molly Winton

>I recently acquired some small blocks of burl, and have been playing around with them. The Tasmanian Eucalyptus piece was fun. It was a very green piece I bought in KC. I wanted to see what would happen if I turned it and branded it prior to drying. When it dried it distorted in, what I think, is a very cool way. The surface also became all bumpy and warpy very much like wet madrone burl will do when turned thin and allowed to dry on it's own. I've got some other pieces waiting for similar pieces.

Upon previewing the post, it seems the descriptions are hard to read. The bottom left piece is the Tasmanian Eucalyptus, while each of the other three are maple burl. Top two are branded and pyrography, while the bottom right has pyrography on the top, and hammered on the base portion. Each piece is approximately 4" diameter and 3" tall.


img

Re: A few recent turnings...

#2

Re: A few recent turnings...

Mike Schwing from Md.

>Wonderful work Molly, as usual. I really love the one in the bottom left corner, especially since I've seen/held one like it that wasn't warped and contorted. The two would make a cool pair! That euclyptus smells nice doesn't it?

Re: A few recent turnings...

#3

Re: A few recent turnings...

John Lucas

>Molly I love the first 2. I think it's the way the black wraps up over the curve that really works. The bottom left piece I like but in the photo the burned area looks like a tie tied around the neck. As a man who hates ties this bugs me. I love the images on the bottom piece but the balance between the bottom and the top portion just seems wrong. I'm not sure why. Maybe the texturing needs to be stronger or the the transition needs to be higher or lower. That's just me. I like the idea. I wonder about a burned thin band to seperate the two areas.

Re: A few recent turnings...

#4

Re: A few recent turnings...

Ed Kelle

>Very nice work Molly. I like that the piece warped on its own, I think it gives more of an aged look which goes very well with your style. I have been heading towards that look as well recently.

About the hammering, I assume that you have to be very careful with doing this on thin works. Is there any kind of settings to control the force, other than just cutting down air pressure? Just curoius for now, I only have my used and abused Dremel to do my texturing work.

Re: A few recent turnings...

#5

Re: A few recent turnings...

Thomas Skaggs, Foothills of Mount Level

>All very nice! Only 4" in diameter? I would have guessed much larger. That detailing is even more impressive knowing at what scale you are working. Terrific!

Tommy

Re: A few recent turnings...

#6

Brad Vietje

These are great !

Brad Vietje

>These are great, Molly ! I love the simple, graceful, ancient shapes, which work well with the woodburned designs. Reminds me of prehistoric drawings like Lascaux Cave. I also agree with John that the vertical band on the wrinkled Eucalyptus piece isn't quite working for me -- at least not in this view. Not sure why, or if I will still feel that way in 30 minutes, but my first impression was to ask what was meant by that, and I suspect it takes away from the other elements.

...sure hope someone buys my house soon so I can get into a new shop and make use of all this excellent inspiration here at W/C !

Safe Spinning,

Brad Vietje

Thetford, VT

Re: A few recent turnings...

#7

Re: A few recent turnings...

Ben Aragon

>Molly,

I really think your work is great and I especially like the vessel on the bottom left.

Best Wishes,

Ben

Re: A few recent turnings...

#8

Re: A few recent turnings...

georgetroy

>Good Golly Miss Molly looks like you have been horsing around. Thanks for showing your unique work. GT

Re: A few recent turnings...

#9

Thanks everyone

Molly Winton

>John, thanks for your feedback. After you mentioned the placement of the break on the bottom right piece I had to go back and study it again. I think you're right that the break could look better a little higher. It's close, but would be just that much better a little higher. The bottom left piece is a very hard one to view in 2D. The distortion is such that it looks very different with just a minor rotation. The necktie look is an anomally. This piece was made similarly to my other 'story' pieces. The branding surrounds three seperate story panels. If I rotated it an 1/8 to the right you would see a very different scenario.

Ed, you do have to be careful hammering fairly thin pieces. I used to hammer with my air hammer, and the only way to regulate the force of the blow was to adjust the air pressure and how close you hold the hammer next to the work. I recently purchased a needle scaler to attach to my air hammer, and now hammering is a total joy to do. It has a much gentler strike and it is done in a fraction of the time the hammer took. I also get a much more uniform coverage. I highly recommend this technique. The beauty of it is you can get the air hammer for about $10, and the needle scaler for about $12 at Harbor Freight. You have to round off the ends of each pin on the scaler though prior to use.

Re: A few recent turnings...

#10

2 alternate views

Molly Winton

>John, here's a better angle to see the blending of the branded areas. These are taken from the top and bottom of the piece. You can also get a better idea of it's overall movement.


img

Re: A few recent turnings...

#11

Re: A few recent turnings...

Jim Shaver - Oakville, Ontario

>Hi Molly,

I enjoy seeing what new creations you have made, top left is my Favorite!

Take care,

Jim

Re: A few recent turnings...

#12

Thanks Jim!

Molly Winton

>

Re: A few recent turnings...

#13

Re: A few recent turnings...

Carole in VA

>More really fascinating work, Molly! Your patience astounds me. I really like the way they warped. In fact I like it better than I do unwarped pieces...adds to the primitive theme.