Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

McNaughton Coring Tool Issue - Little long

Posts

McNaughton Coring Tool Issue - Little long

#1

McNaughton Coring Tool Issue - Little long

Brodie Brickey - Long Beach, CA

>Back when I had my smaller delta lathe I bought the Kel McNaughton coring tool. I was able to use it on that lathe despite the 500 RPM and the limit of 14" bowls. Last weekend I went out to core a nice piece of 15" maple and found that the post for the coring system didn't bring the blade up level with the horizontal center on my new Powermatic 3520a. Its been the advice of turners like Mahoney and Grumbine that you need to be at horizontal center to be most effective. The problems I had with the system on my previous lathe evaporated when I followed that principle.

Has anyone else had this problem?

I went over to Woodcraft and they didn't have any longer posts for the tool. I just got done sending off an email to McNaughton so we'll see what they say, but it looks like I'm going to have to scare up a machinist locally to get a post duplicated and lengthened.

Anyone in SoCal have a good machinist?

Any other ideas would be greatly appreciated.

Brodie

Re: McNaughton Coring Tool Issue - Little long

#2

Re: McNaughton Coring Tool Issue - Little long

Norm Smith in Nova Scotia

>Hi Brodie,

I had to extend the lenth of some tool rests for the same reason. What I did was cut the post off at the bottom of the rest and had a welder weld a 1"x 5" steel bar in its place. Do not add a piece to the existing bar because the weld will not operate smoothly.

Norm

Re: McNaughton Coring Tool Issue - Little long

#3

Brad Vietje

Re: McNaughton Coring Tool Issue - Little long

Brad Vietje

>Brodie,

You definately DO want to be at center height (or a tiny bit higher) but never below center with that system. It will bind pretty badly (and reliably) if the tip ever goes below center. Please let us know how you make out -- I would think McNaughton would provide a longer post for you. I may be putting mine on the same lathe someday soon, so I'd like to hear what you find.

Safe Spinning,

Brad Vietje

Thetford, VT

Re: McNaughton Coring Tool Issue - Little long

#5

Re: McNaughton Coring Tool Issue - Little long *LINK*

Gerry in Maryland

>Maybe Greg Jensen can help you too!

Gerry


Kelton Rep's previous response

Re: McNaughton Coring Tool Issue - Little long

#6

Re: McNaughton Coring Tool Issue - Little long

Eduardo Sarmiento Hall-Lima Peru

>I had the same problem and I use an extra piece of iron plate to compensate the altitude,under my tool rest post

Re: McNaughton Coring Tool Issue - Little long

#7

Re: McNaughton Coring Tool Issue - Little long

Frank Martin

>I was indeed able to get the longer 4" post to fit my Powermatic and it works great. my understanding is that not only can you get the two different lengths in the 1" post, but also different diameters if necessary. finding someone who knows what you are talking about is a different problem altogether. In my case I was able to get the longer post from the Woodcraft where I purchased mine. I'll check in later from home, but there is at least one supplier who sells the alternate posts for $15 - $20. I'll send the link.

frank

Re: McNaughton Coring Tool Issue - Little long

#8

Re: McNaughton - Try here for long post

Frank Martin

>try here for long tool post for mcnaughton (scroll down until you see it) http://www.cuttingedgetools.com/Onlinecat.htm/WebCatalog/CenterSaver.html

good luck, frank

Re: McNaughton Coring Tool Issue - Little long

#9

Re: McNaughton - Try here for long post

Brodie Brickey - Long Beach, CA

>Frank,

Thank you for the link. I've ordered one and should be receiving it in a couple days.

Regards,

Brodie