Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Skewer Tips and Tricks...

Posts

Skewer Tips and Tricks...

#1

Skewer Tips and Tricks...

Larry In Lima

>I am planning on making quite a few barbecue skewers for the family (shishkabobs). I know the principal is simple enough, drill hole in one end for the metal skewer, turn the wood round, maybe epoxy the skewer in the hole, use a ferrule.

I'm thinking handles 3/4" round, 4" long. Stainless steel for the skewer. Flat steel stock, but still thin might be best, to keep the food from spinning around on the skewer once on the grill.

Questions - where would be a good place to buy stainless steel in an appropriate size (1/8" thick, 1/4" wide, 14" long once cut?), and what is a good heat resistant wood, available in maybe 1" square stock? Source of wood and a recommended finish?

Anyone done this, and what did you do, what would you do different? I know this isn't rocket science for something like this, but considering I may make about 60 of these, I'd like to do it "right" and very well the first time!! Thanks. Larry

Re: Skewer Tips and Tricks...

#2

Re: Skewer Tips and Tricks...

Ron in Drums PA

>Here in the states we can buy a dozen skewers for about a buck. We can't buy the materials for that price.

Re: Skewer Tips and Tricks...

#3

Re: Skewer Tips and Tricks...

Larry In Lima

>Well Ron, it's not about the money, it's about the quality of the skewers and making it myself. I guess I could also tell you that I can buy pens for .19 cents, wood bowls for a buck at Dollar General, and the list goes on.... Larry

Re: Skewer Tips and Tricks...

#4

Re: Skewer Tips and Tricks...

Ron in Drums PA

>I didn't mean it that way. I meant no offense.

Re: Skewer Tips and Tricks...

#5

Re: Skewer Tips and Tricks...

Joe Herrmann

>You might be better off buying the inexpensive skewers and knocking the handle off. Then you can make your own handles to re-fit to the metal skewer. It might be cheaper in the long run rather than to buy the steel and cut it to size, etc.

Just an alternative suggestion in case you can't find the steel at a reasonable cost.

Joe

Re: Skewer Tips and Tricks...

#6

Re: Skewer Tips and Tricks...

Larry In Lima

>No problem, same here... Just meant that I think just about everything we do woodturning wise (and maybe everything period) seems to be cheaper when made by some "3rd world" country. I'm just interested in making something very classy, and durable when the family gets together. All of my family is very in to eating and barbecues, so this looks like a fun, although admittedly expensive project.... Dissasembling some and "remaking" them is an idea though! Thanks guys. Larry

Re: Skewer Tips and Tricks...

#7

Re: Skewer Tips and Tricks...

William Duffield, on the Cohansey

>I don't know of any wood that will stand up to the heat of a BBQ grill for very long, and epoxy is even less heat resistant, usually losing its strength somewhere around 200° F. You might want to consider turning the handles from brass instead of from wood, and soldering or brazing them to the stainless skewer stock.

Re: Skewer Tips and Tricks...

#8

Re: Skewer Tips and Tricks...

John K Jordan

>>I don't know of any wood that will stand up

>to the heat of a BBQ grill for very long

Last year I finally had to replace the nozzle on my woodstove bellows which gets a lot of use VERY close to the coals. I used cocobolo which, although hard to tell after just one season, seems to be holding up better than the original red oak nozzle I had made about 5 seasons earlier.

JKJ in East TN

Re: Skewer Tips and Tricks...

#9

Re: Skewer Tips and Tricks...

William Duffield, on the Cohansey

>The scenario I was imagining was the whole skewer, including the handle, inside the fire box, with the lid closed, for ten minutes or more. That's what I based my recommendation on, because my stainless skewers are short, and that's where they end up. If one can manage to build long enough skewers that the handles remain outside the fire box, then the density and other characteristics of different woods are definitely worth discussing. On one BBQ grill I had, I replaced the original handle, bolted to the side of the lid, after it had charred, with a turning of live oak. That held up very well, even unprotected from the harsh weather in southern Florida. OTOH, live oak makes excellent coals for BBQing :^) Maybe that's because it burns slowly, which might be a characteristic worth looking at for handles. Might be a reason to consider mesquite, too?