Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Ballast

Posts

Ballast

#1

Ballast

Don Orr

>As kind of a follow up to the Delta/Mini stand thread below, I want to add some mass to my lathe and want to know if sand (or gravel) is the only solution. Can I use large steel plates (like front end tractor weights) instead ? Or does the looser material help absorb vibrations better. I do like the idea of coarser gravel instead of sand. Harder for it to escape and cause problems. But it takes up so much space for the weight. What are my real options ?

Thanks for any advice, Don

Re: Ballast

#2

Iron

Barbara Gill, Remlik VA

>When I was using my home made stand for my first lathe I used piggs of iron, each weighing 50#, in the box beam. Worked very well. The combined weight of stand and lathe was around 1,000#.

Re: Ballast

#3

Re: Ballast

John Lucas

>Don I piled those concrete filled plastic weight lifting weights on my first lathe. The second one had a stand made from Pressed wood and was filled partially with sand. I think anything works. Sand, Lead shot and Gravel probably absorb more vibration but it would be interesting to see a test on that. I suspect a lot more things come into play, such as the way the stand is built, how the lathe is attached to the stand and where the weight is located etc.

Re: Ballast

#4

Re: Ballast *LINK*

Fred Holder

>When I built the stand for my Nova DVR 3000, I used 2"x6" boards throughout for the framework. This gave me a box section near the bottom the width and length of the stand and 5.5" deep. I filled it with railroad spikes that I had on hand, plus a few stamping dies. It has provided a very good and stable base for my lathe. The lathe sets solid with as large of pieces as the lathe is capable of turning, up to 16" diameter. I suspect that tractor weights with the space between filled in with old nuts and bolts would make a pretty good ballest for your lathe.


Fred Holder's Domain Site

Re: Ballast

#5

Re: Ballast

Wally Dickerman in Arizona

>Sand is heavier for it's volume than gravel. It really isn't too difficult to construct escape-proof containers.

It's been pretty well established that loose materials will dampen vibration better than solid materials.

Years ago I did a lot of shotgun shooting (skeet and trap) and reloaded my own shells. I had a lot of lead shot, which came in 25 lb. bags. I used several bags to weigh down my lathe. Much less volume than sand or gravel or even steel. Best material for dampening vibration that I've found, but it's expensive.

Wally

Re: Ballast

#6

Re: Ballast

Mike Schwing from Md.

>I have 300# of sand in my ballast box, but agree with Wally that lead shot is going to be better. I did a lot of reloading, too, Wally. Shot competitive skeet for a while, lots of bags of #9's still somewhere in the basement.

Re: Ballast

#7

Re: Ballast

woodspinner/ Bill Hale

>I agree that any weight is good.

Remember that someday you may want to move the lathe so add weight in a form that you can also remove.

Bill in Dolores Co.

Re: Ballast

#8

Re: Lead Ballast

Carol Reed, the Router Lady, Dubuque

>When I needed ballast, I went to Discount Tire (then managed by a friend of mine)for old wheel weights. Turns out they had to pay to dispose of them, so they were more than happy to load my truck with more than I could ever use.

Re: Ballast

#9

Re: Ballast

Roger Smith

>Don, Diversified Products in Opelika, AL uses a very heavy material to make lifting weights. This stuff is several times heavier than sand. It will also set up hard. You might contact them or some other lifting weight manufacturer for a source.

roger

Re: Ballast

#10

Re: Ballast *LINK*

Mark Mandell - Gone Round In Jersey

>Don,

Don't know if your lathe will lend itself to this, but the information on the end of this link is very interesting. I don't use it, my 850# Stubby refuses to move, but you may give it a shot (bird, buck, or otherwise).

Mark


A Little Leverage

Re: Ballast

#11

Dick Hines

Re: Ballast

Dick Hines

>I guess you would have to use steel shot now. The feds will try to save you from lead poisoning.

Re: Ballast

#12

Re: Ballast

woodspinner/ Bill Hale

>Even my 1000# Oneway will move if I screw up on start speed in the rough.

Bill in Dolores Colorado

Re: Ballast

#13

Tie

Mark Mandell - Gone Round In Jersey

>Yer kangaroo down, Sport!

[But don't ignore the speed control, either.]

M

Re: Ballast

#14

Re: Ballast

Don Orr

>Thanks a TON (pun intended)to everyone for all the great suggestions and ideas. I don't have a Stubby or Oneway yet but my Jet 1642 gets a little wobbly with out-of-round blanks. I'll get her settled down now though.