Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Which HVLP system you guys use

Posts

Which HVLP system you guys use

#1

Which HVLP system you guys use

Sascha

>i am in the market for a HVLP spray system and i am leaning towards the fuji Q4.

i will be building a really tiny spray booth, something i can take apart after spraying sessions. i just want to be able to get a high gloss finish on some of my turnings.

which systems do you use/have/like and why. any help would be greatly appreciated. some links would be awesome, too.

and if you guys have any pics af laquered pieces, post them, just to get ideas.

thank you so much in advance

sascha

Re: Which HVLP system you guys use

#2

Re: Which HVLP system you guys use

Joel Hunnicutt

>If you have a compressor, think about a conversion gun. You can get anything from a harbor freight gun for $40 to a Sata for $500. Gravity guns don't use much air and you avoid the problem of heat that you get from a turbine. I spray with a walcom fx geo that Jeff Jewitt sells on Hmesteadfinishing.com It gives a first class finish off the gun.

Re: Which HVLP system you guys use

#3

Re: Which HVLP system you guys use *LINK*

Mark Mandell - Gone Round In Jersey

>Sascha,

If you're looking to use solvent lacquer in a gun system (as opposed to spray cans), you do NOT want a turbine system like the Fuji, Apollo, Wagner, etc. because all of those units warm up the air as it passes through the turbine unit, and the hot air will gel or dry your lacquer before it gets from the gun's tip to the wood surface. The self-contained turbine systems are designed for waterborne finishes were the warming of the finish in the gun helps with the finish drying on the surface.

If you have a compressor, a pressure gun may be your better bet, especially for solvent finishes like NC lacquer and shellac, although for small items like turnings I think you'll find that a spray can that saves you all that setup time and cleaning, etc. will be your best option for lacquer finishes, although a small compressor and either a touch-up gun or one of the little Critter sprayers will do well without much expense. Of course, if you're into spending the bucks, look into the Asturo and Walcom gun sets with pressure feeds etc. I have an Asturo with a 2-quart pressure pot for flatwork finishing that will lay down waterborne or solvent finishes almost glass smooth off-the-gun.

Please remember that you should not be spraying finish in an enclosed space. Your "booth" needs to be exhausted outside, and you will need a real, properly "organic vapor" rated, filter mask. Actually, you should have one of those even if you use a spray can.

You will do well to visit Jeff Jewitt's website at the link. You can ask your questions of Jeff directly and also post them on his finishing forum.


Homestead

Re: Which HVLP system you guys use

#4

Re: Which HVLP system you guys use

Sascha

>thank you so much mark, that is what i was looking for. it makes sense. i am calling jeff today and heave him recommend something to me. by the way, the booth will be somewhat outside, not inside anyway, i have no space. more and open garage door kinda thing, with a fan and a respirator. which one should i get, i know i need a charcoal one.

thanx guys

sascha

Re: Which HVLP system you guys use

#5

Re: Which HVLP system you guys use *LINK*

Gary Ratajczak

>I have had some really good luck with this gun. Price was right for my budget.


http://gleempaint.com/hvcongunnew.html

Re: Which HVLP system you guys use

#6

Re: Which HVLP system you guys use

John Lucas

>I use the HF touch up gun. It's easy to clean, holds enough finish for most of my turning projects and was really cheap. I thought it would be junk but wanted to try spraying. I've really enjoyed using it. I did buy one of their bigger guns but have yet to use it.

Re: Which HVLP system you guys use

#7

Re: Which HVLP system you guys use

Mark Mandell - Gone Round In Jersey

>I use the 3M organic vapor mask. Costs about $40, but does the job and is comfortable to wear. I keep mine in a sealed bag between spraying sessions; otherwise the filters deactivate or degrade and have to be replaced each time you use the mask; that gets kind of expensive.

M

Re: Which HVLP system you guys use

#8

Re: Which HVLP system you guys use

woodspinner/ Bill Hale

>If you are not doing production work stay with the spray cans.

No prep. No cleanup I do a lot of work and still use spray cans for finishing. If you consider the cost of the cans at a Home Depot or Walmart, the number of finishes per can, the cost of solvent for clean up against a new system I believe you will find the can cost to be effective.

I can pop into my booth, spray a piece and walk away. Bigger is not allways better!

Good turning and be safe

Bill in Dolores, Colorado

Re: Which HVLP system you guys use

#9

Re: Which HVLP system you guys use

Darryl Hansen

>Try the Critter. About $40 on Amazon.com. Uses about 40# for lacquer. I have a cheepy compressor that has a 6 gal tank puts out about 150# and 3.2cfm air flow. Works great. Particularly since the critter uses a mason jar as its paint reseviour. cleans is a second by putting thinner in another jar and spraying. Simple but does the trick.

Re: Which HVLP system you guys use

#10

Re: Which HVLP system you guys use

Joe Flemig

>Bill offers sound advice. Depending on the amount that you are spraying, cans will do the trick. I do both and can offer this comparison. For cans, I've used Deft gloss lacquer. I can get it to flow nicely without runs. The down side is that it takes a LOT of coats to build the kind of finish I desire. For me, 20 to 30 applications.

My spray gun is a Sharpe product: Finex HVLP 100 mini gravity feed gun (around $80 from Spraygundepot.com). I can use a high body lacquer straight out of the can and get a thicker build in 5 or 6 coats compared to the previous. As Bill points out, however, there are many costs. For me, I had to buy a compressor, filter, regulator and gun. You also have to mess around with cleaning the gun. I use the gun for batches of pieces to minimize the impact of set-ups. I will admit, however, that the finish I get with the gun is compelling enough for me to use it for one-at-a-time pieces too.

Joe Fleming - SanDiego

Re: Which HVLP system you guys use

#11

Re: Which HVLP system you guys use

Sascha

>yeah, i tried the deft in a can and i can't say i love it. the nozzle worked ok at first, but after a while started spitting a bit too much for my taste.

i'll call the guy mark recommended tomorrow and see what he thinks. i'll get a nice setup since i want to use it occasionally on furniture as well, not that i am building much since i started turning, but you never know

thanx so much guys

sascha