Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Thread cutting jig?

Posts

Thread cutting jig?

#1

Thread cutting jig?

Robert Henderson

>I have an old craftsman lathe with 3/4"-16 MT#1 headstock. I'm trying to rig it up to make threaded-lid boxes.

I have a 60 degree cutter with a 1/2" shank.

Is it safe to use my MT1 drill chuck in the headstock to hold the cutter?

If not, is there an adapter I can get that screws on the 3/4"-16 spindle and gives me a MT2 so I can use a 1/2" collet with drawbar?

Or any other suggestions?

Re: Thread cutting jig?

#2

Re: Thread cutting jig?

Ed Moore

>I would check with Vic at Best Wood Tools and see what he recommends. Maybe he has a #1 Morse taper drawbar and collet system.

Re: Thread cutting jig?

#3

Re: Thread cutting jig?

Don Evans

>If you want to pursue your idea in this manner, I don't see why you don't just modify (go to machine shop if you have too) the MT1 drill chuck to take a drawbar?

To answer your question, yes, it would be sort of dangerous to use it without a drawbar to hold it securely. Vibration will definitely loosen it which will cause ruined work and much frustration.

I would drop the extension idea, it would extend the cutter too far out and it's just more distance to try and hold true. Going to all that trouble just because you have a 1/2" cutter isn't worth it.

You really haven't touched on the hard part either, that is holding the box. You'll need some form of x y vise or table to move the box and position it to the cutter and also an acme screw and nut to turn the box. The tpi of the acme will determine the tpi you can cut and unless you can change it you are stuck with one thread.

Have you considered learning to do it by hand? Hand chasing isn't really that hard IF you have someone to help you get started, club maybe?

By the time you put all this together, you could learn and be doing it by hand.

Fred Holder has a book on the subject and he may jump in here hopefully.

Doing it by hand is much more rewarding also.

Don

Re: Thread cutting jig?

#4

Re: Thread cutting jig?

John Lucas

>If your headstock has a hole all the way through then drill and tap the end of your #1 morse taper drill chuck and use a draw bar. When a Jacobs chuck with taper comes loose in a the spindle it isn't dangerous but it would mess up your threads and that's not good.

The Beal collet system threads on the spindle instead of using a morse taper. If they make one in 3/4 x16 it should do what you want.

Bestwoodtools also has a new collet system but I haven't looked at it closely enough to tell you how it works.

Re: Thread cutting jig?

#5

3/4 x 16 collet set *LINK*

Phil Joines Krum, Texas

>Little Machine Shop carries the Taig collet set, Unfortunatly, it onlt goes up to 5/16". I don't know if a thread cutter is available that small. It screws on the outside of the spindle. I've found them to be more acurate that MT mounted collets.

If your 4 jaw chuck is acurate enough and the slides come close to meeting in the center it might hold the cutter with the jaws removed.


Taig Collet Set

Re: Thread cutting jig?

#6

Re: 3/4 x 16 collet set

Fred in NC

>I agree with Phil about the collet set from LittleMachineShop. I have it myself.

Maybe getting a 60 degree cutter (mill bit) with a smaller shank will also help. Then it will fit the collet set.

Re: Thread cutting jig?

#7

Re: Thread cutting jig?

Robert Henderson

>I've always thought it would be very cool to cut threads by hand, but it looks so daunting in books and I've never seen it being done. I also read somewhere that it takes years of practice to do it at all well. Maybe I need to take another look at the idea, Thanks for the suggestion.

Re: Thread cutting jig?

#8

Re: Thread cutting jig?

Robert Henderson

>Thanks for all the help! I'd be spending a lot of time staring at my shoes and wondering what to do next if all you folks weren't so generous with your knowlege and experience.

I went to the Beall site and they have a morse taper #1 that is tapped for a draw bar. It ends in a 5/8" rod with a flat for attaching one of their buffer adapters with set screws.

Woodcraft has a 1/2" keyless chuck that mounts on a 5/8" motor shaft with set screws.

I think that's the way I'll go.

Again, thanks for all the advice, past, present, and future. Someday I'll know enough to contribute.

Re: Thread cutting jig?

#9

Re: Thread cutting jig?

Hawaii Turner

>Robert,

Go to this link and get some ideas.

http://www.jeanmichel.org/thread.htm

Jean was a frequent contributor to this site and has a neat websith that is still on the web.

R.I.P., bro Jean, we still think of you fondly.

Aloha, Doug

Re: Thread cutting jig?

#10

Re: I corresponded with Jean a few months ago.

Al Crandall--NE of Indy--

>I told him I was impressed with his jig, and he tried to send me detailed drawings of his jig. They didn't come through, though. I just guessed at the dimensions, added some personal refinements, and completed the jig about two weeks ago. Pictures and details of my version of Jean's jig can be seen at www.cicaaw.org web site. Open the link to "August's meeting pictures". There are seven photos of it and also a small bowl I knocked out to display the threading capabilities of this jig. Jean's jigs are all well designed.