Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

PM3520a wrench replacement needed

Posts

PM3520a wrench replacement needed

#1

PM3520a wrench replacement needed

Bob Persing (Skillman NJ)

>Hi folks,

I have a PM3520a and, although being quite pleased with the lathe, I absolutely do not like the wrenches supplied with the lathe. They are quite narrow and will dig into the shaft or faceplate kinda messing them up. I would like to know if anyone has a creative source for replacement wrenches that will not cost me a fortune. Sizes needed for chucks (Nova) spindle and faceplates are about 1.5" and 2". Open-end wrenches at Sears are about $30 to $40 each (too much $$ for me). I have not found anything used (so far).

Suggestions welcome!

Thanks for your help.

BobP

Re: PM3520a wrench replacement needed

#2

Try this..

W.C. Turner

>I've got a large strap wrench that works very well for certain applications. Give it a try, I think you'l e pleased.

wct

Re: PM3520a wrench replacement needed

#3

Re: PM3520a wrench replacement needed

Gerry in Maryland

>Bob,

They sell adjustable slip nut wrenches at HD and Lowes in the plumbing department. They are used to tighten trap nuts on sinks and wash basins.

Gerry

Re: PM3520a wrench replacement needed

#4

Re: PM3520a wrench replacement needed

John Lucas

>Bob You must have a different wrench that I got. Mine is cast iron and the jaws are at least 1/2" wide. I've never used it. I don't tend to tighten my chucks and such that much so I've been able to remove them using the spindle lock.

Re: PM3520a wrench replacement needed

#5

John, mine’s a big mamma-jamma too!

Gerry in Maryland

>

Re: PM3520a wrench replacement needed

#6

Re: John, mine’s a big mamma-jamma too!

Sonja Lemon Sacramento Ca.

>The chuck on my small Jet often jammed. The solution was to use a plastic washer behind the chuck. This prevents it from overtightening and facilitates removal by hand. If only a thin washer is needed, cut one from the plastic lid of a coffee can. Thicker ones are available commercially. This may not solve your problem, but it sure helped mine! Sonja

Re: PM3520a wrench replacement needed

#7

Flea market or swap meet

Paul in Phoenix, AZ

>

Re: PM3520a wrench replacement needed

#8

Re: PM3520a wrench replacement needed

Mark Kauder, Phenix City, AL

>Go to the local big box plumbing department and buy a slip-nut wrench. It is a large - cheap ($10) crecent wrench made to be used on the nut on a sink drain.

I have several, and have locked them in place for use with my chuck, and with faceplates.

I wrote this one up for the AAW Journal (thanks John Lucas) a few months back.

I am also a big one for picking up cheap crescent wrenches of all sizes at yard sales and having them handy all around the shop.

Mark

Re: PM3520a wrench replacement needed

#9

Re: PM3520a wrench ...but...

BobP

>Well, I have had my 3520a for quite some time now, at least 3 or 4 years I would guess. My wrench is only about 3/16" wide...,if it were 1/2" it would not tend to mung up the shaft as much. I think I could call PM and see about purchasing a replacement as the heavier wrench must be an newer item. Here is more detail about the need for the wrench vs the spindle lock...my "real chuck is a large Axminster. To release this chuck you have to insert the locking wrench and give it a whack. It is hard to hold the spindle lock, steady the chuck wrench and swing the mallet. The second need for a similar wrench is for my SuperNova chuck. I like it to grip the spindle tightly as there is no set-screw to lock it in place for when you reverse direction. To remove the Nova from the spindle I need to use a wrench. I am presently using a very old "monkey wrench" that I have ground down to be thinner...not the best thing going.

Thanks all for the tips.

BobP

Re: PM3520a wrench replacement needed

#10

Re: PM3520a wrench replacement needed

BobP

>Thanks for the suggestion Mark.

I will have to look in the plumbing dept.

I too have quite an assortment of adjustable (Cresent) wrenches but none open large enough for my SuperNova chuck.

BobP

Re: PM3520a wrench replacement needed

#11

Re:Do you live near a Tractor Supply Store?

Al Crandall--NE of Indy--

>I have bought several large open end/box end combo wrenches for occasional use at TSC stores. I don't think I have had to pay more than $8 or $9 for any of them. That being said, the last time I needed a large (2") wrench for the nuts which I have turned into faceplates, I just sawed one out of a piece of 1/4" thick plate steel. It was finished before I could have driven to TSC and back.

Re: PM3520a wrench replacement needed

#12

Re:Do you live near a Tractor Supply Store?

Bob Persing (Skillman NJ)

>Thanks for the suggestion Al.

I guess I can't see myself grabing my hacksaw and cutting into 1/4" steel plate so I'll have to pass on that one.

Farming is all but totaly dead in the "Garden" state of New Jersey but there ARE some tractor dealers remaining in my area. It's worth a look as the price is right in my range.

Thanks

BobP

Re: PM3520a wrench replacement needed

#13

Re:Do you live near a Tractor Supply Store?

Ed Karch

>Check out the tools in antique stores. They often have old tractor wrenches.

Ed

Re: PM3520a wrench replacement needed

#14

Re: PM3520a wrench replacement needed

Brodie Brickey

>Bob,

You mentioned its hard to engage the spindle lock and do everything else while using the Axminster Chuck.

If you look at the wings to either side of the spindle lock you can drill a hole through the wings so that a pin will pass through and keep the spindle lock down. Make sure the pin has a long handle on it that covers the stop/start button so you can't engage the motor without dis-engaging the spindle lock. This should help you with one of your problems. The strap wrench mentioned in other posts should resolve the other problem.

Regards,

Brodie

Re: PM3520a wrench replacement needed

#15

Re:Do you live near a Tractor Supply Store?

John K Jordan

>Northern Tool also has inexpensive wrenches in large sizes. I bought sockets and wrenches there to work on my tractor.

JKJ in East TN