Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Handwheel on Powermatic 3520A

Posts

Handwheel on Powermatic 3520A

#1

Handwheel on Powermatic 3520A

Dawn Adams

>I am trying to remove the handwheel from my Powermatic to install a vacuum chucking system. I called Powermatic first to make sure I was doing this correctly. They said to remove the two set screws and turn clockwise to loosen. I did just that - using a large pipe wrench on the handwheel. After much struggling, the handwheel did begin to move, but only counterclockwise and it just spins. It is very tight, but it turns in both directions. Even the spindle inside of it just turns with it. HELP - where did I go wrong. Any suggestions on what to do to fix it?

Re: Handwheel on Powermatic 3520A

#2

Re: Handwheel on Powermatic 3520A

Norm Smith in Nova Scotia

>Hi Dawn,

I use a steel forked pry bar on mine. It works fine. My spindle under the hand wheel is not threaded.

Norm

Re: Handwheel on Powermatic 3520A

#3

Re: Handwheel on Powermatic 3520A

John Lucas

>I was thinking mine wasn't threaded as well. Probably the set screws have been tightened enough that they have pushed the metal up around the point. This makes them very hard to remove. Take a drill bit that is the exact size as the threaded hole in the handwheel and just push it in very slightly with the drill running. You don't want to drill a hole, you just want to remove that burr. Twisting the handwheel like they say sometimes will push the burr down so you can pull the wheel off.

Re: Handwheel on Powermatic 3520A

#4

Re: Handwheel on Powermatic 3520A

John Lucas

>I forgot to mention, depending on the vacuum system you use you may have to calk the handwheel to keep it from leaking through that. I had my handwheel bored to fit the Nova bearing vacuum adaptor because I already had that.

Re: Handwheel on Powermatic 3520A

#5

Re: Might be easier to just leave it on.

Al Crandall--NE of Indy--

>I have made vacuum adapters for several lathes, and I use a lamp rod through the spindle to transfer the vacuum from the bell to the rotary adapter. No need to remove a hand wheel if this is your system.

Re: Handwheel on Powermatic 3520A

#6

home made EZ vac adaptor

john Lucas

>I'll try to post the plans for this. If it doesn't work e-mail me. I can send a file this size over e-mail.


img

Re: Handwheel on Powermatic 3520A

#7

Re: home made EZ vac adaptor

john Lucas

>I should have reduced the size it cut off both sides. If you don't understand how to build it e-mail me and I'll send you the full file.

Re: Handwheel on Powermatic 3520A

#8

Re: home made EZ vac adaptor

Phil Powell

>Get yourself a copy of the Fall 2005 issue of "Woodturning Design".

There is an excellent article on just this subject. Vacuum chucking!

Re: Handwheel on Powermatic 3520A

#9

Re: home made EZ vac adaptor

Stuart Johnson

>John, I have an EZ vac adaptor and it works great. Where did you get the parts to make yours?

Re: Handwheel on Powermatic 3520A

#10

Setscrews

Fred in NC

>I don't own that model lathe.

However, sometimes I have found more than one setscrew in the same hole. Like I take out the setscrew, and find another one deeper in the hole. It acts like a locknut. Worth checking into.

Re: Handwheel on Powermatic 3520A

#11

Re: home made EZ vac adaptor

John Lucas

>Stuart I bought all the parts at Lowes. There's one part that I can't remember the name of. It is tapped in the middle for the lamp rod and has 2 long slots on each side. It is designed so that you can hang lamp rod from an outlet box in the cieling. I cut the ends off so that it would fit in the turned Hand tensioning knob. I basically just drilled a piece of wood. Then cross cut it and glued the threaded metal piece in place. Then I slotted the other piece of wood to fit around the metal and glued it all back together. Then it was a simple matter to mount this between centers and turn it to shape.

This was easier than trying to capture a nut or something similar in the knob to tighten up on the lamp rod. The front end that goes in the inboard side of the spindle is just a piece of wood that was turned close to a #2 morse taper and then center drilled 3/8" . Then it is glued in place.

Re: Handwheel on Powermatic 3520A

#12

Re: Setscrews

Dawn Adams

>I found my model also had two set screws in one hole. What a suprise after removing one and trying to turn the wheel (which would not budge) that there was another set screw in the hole. I still do not have the handwheel off, but I am going to try just pulling it off since it seems that it is not threaded (although Powermatic says it is).

Re: Handwheel on Powermatic 3520A

#13

Re: home made EZ vac adaptor

Al Crandall--NE of Indy--

>I just used connector sleeves to fit the lamp rod. I drilled a hole in the "whatever" and used thick CA glue to hold the sleeve in place. They are about 5/8" long and come in packages of two at Lowe's. Quick and dirty internal threads in less than a minute with no machining.