Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Experiences with "leopardwood"?

Posts

Experiences with "leopardwood"?

#1

Experiences with "leopardwood"?

GaryG in MD

>I got a small stick of leopardwood in an eBay auction because it looked cool in the photo. This is strange stuff. When I received it and examined it closely, I was surprised to find that it's very rough, ropey, and holey, almost like a very fine-grained "pod", if you will. When viewed closely, a large percentage of the "spots" are badly torn out, leaving significant, irregular voids. At 90 degrees to the spots, the surface is very fibrous with lots of nearly-microscopic, lens-shaped voids.

What bothers me is all the small holes -- which seem to arise from two different phenomena in the two perpendicular orientations. In the "spots" orientation, is this just the way it is, or could it be the result of the tearing of the grain by the saw? Will it cut cleanly on the lathe or should I expect a rough, holey surface in the final product?

Is this character usual for this wood, or do I just have a strange piece? Does this stuff ever finish up anything like smooth, or should I expect to leave it with a very rough surface which shows off that strange cell structure? I feel like filling the grain, as one would with oak, would defeat the purpose of buying this kind of wood in the first place.

Not unexpectedly, the character of the surface depends VERY much on the grain orientation in the finished piece (say, e.g., a bottle stopper). How does this stuff turn? What is the best orientation for the turned piece to show off the pattern (end grain or cross grain)? What is the best way to finish it?

Thoughts and recommendations please... ...Gary

Re: Experiences with "leopardwood"?

#2

Re: Experiences with "leopardwood"?

Larry

>I think you got ripped off. The leopardwood I've seen is very dense, heavy and hard.

Re: Experiences with "leopardwood"?

#3

Re: Experiences with "leopardwood"?

oldgriz

>I have to agree with Larry... does not sound like any leopard wood I have ever seen... could you post a pic of both sides..

Re: Experiences with "leopardwood"?

#4

Re: Experiences with "leopardwood"? *LINK*

Russ Fairfield

>Go to the link for photos of Leopard.


Leopardwood photos

Re: Experiences with "leopardwood"?

#5

Re: Experiences with "leopardwood"?

Mark Kauder, Phenix City, AL

>A few years ago, I was visiting my parents in Phoenix, AZ. My Dad and I visited a local wood supplier, and I happened to see some Leopard Wood. I looked just like the pics that Russ has posted. I though it was neat, but that was that.

About 6 weeks later, on my birthday, I came home from work and saw a package on the front poarch. It was about 48"x3"x4". IT WEIGHTED A TON. I wondered what my parents could have sent me made of cast iron or Steel? Turned out be a piece of Leopard Wood.

Just told the story to illustrate that this is a very dense, heavy wood. It weights 63-84 lbs cu ft. By contrast Ash is 41, Purpleheart is 51-66.

I made some candle stick holders from it - they would be great in a fight.

Short story - if your wood is not dense, it could be a wood, sometimes calle Leopardwood, that comes from Austrailia, instead of South America.

Mark

Re: Experiences with "leopardwood"?

#6

Re: Experiences with "leopardwood"?

Dave Anderson Chester, NH

>In addition to Russ's photos you might want to look up snakewood. It is often called Leopardwood and has a specific gravity slightly denser than that of Lignum vitae. It is gorgeous and turns very well but it is notoriously unstable and prone to cracking and checking without any provocation at all.

Re: Experiences with "leopardwood"?

#7

Re: Experiences with "leopardwood"?

GaryG in MD

>Thanks, all, for your responses, and thanks Russ for the link. That's a good site, which I'll bookmark.

The source from which I purchased this stick is an apparently reputable dealer, so I think it's probably "real", although I have noticed a lot of confusion in the naming of exotic woods -- with some overlaps and contradictions. For example, Mark has indicated that Leopard Wood and Leopardwood are apparently not the same thing. That makes life a little complicated. I also saw one place where they said lacewood and leopardwood are the same thing, but I think that's wrong. It's hard to know what to believe.

I see a tremendous variation in appearance in the photos on Russ's linked site, but what I have here does look like some of the photos, and it is relatively dense. I'll calculate the density when I get a minute. I'll see if I can get some macro photos on later too. Maybe then we can continue this discussion.

I still have to figure out how to turn and finish this stuff.

...Gary

Re: Experiences with "leopardwood"?

#8

Re: Experiences with "leopardwood"?

Mark Kauder, Phenix City, AL

>All Leopardwood is also called Snakewood, but not all Snakewood is called Leopardwood.

The main Leopardwood is Brosimum guianense (family - Moraceae) and is often called Snakewood. The Leopardwood that I had is very stable.

http://www.righteouswoods.net/leopardwood.html

However the Snakewood that I know that is very prone to cracking looks much the same, - I have been unable to find the exact scientific name. I have even seen pen blacks of it packed in water until turning.

Here is one "Snakewood"

http://www.righteouswoods.net/snakewood.html

The problem is the varity of common names associated with most wood.

Mark

Re: Experiences with "leopardwood"?

#9

Latin name

Dave Anderson Chester, NH

>Hi Mark-

The snakewood I use is Piratinera guianensis and comes mostly from the eastern "hump" of South America. Primarily Guyana, surinam, and some form northern casstal Brazil and from Venezuela.

Re: Experiences with "leopardwood"?

#10

Re: Latin name *LINK*

Mark Kauder, Phenix City, AL

>Yeah, same stuff. To confuse matters, Piratinera guianensis is a synonym for Brosimum guianense. Same stuff, same stuff. (I guess.....my head hurts).

Mark

;)


http://www2.fpl.fs.fed.us:8080/tilia/RunPublicQuery.do