Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Vega plus shavings (pics)

Posts

Vega plus shavings (pics)

#1

Vega plus shavings (pics)

Bill Grumbine (Kutztown PA)

>Howdy everyone

As promised, I have some pictures and impressions to share regarding my Vega lathe. This is not going to be comprehensive, but more like a first impression sort of thing. I am sure I will develop a better sense of what this lathe will and won't do as I continue to use it.

On Friday afternoon, I got to spin my first piece of wood on it. While a significant occasion, I am not one who gets all wrapped up in the gravity of the moment - unless gravity takes the opportunity to drop a heavy piece of wood or metal on my foot! :eek: I did not go looking for a special piece of wood, but rather I selected a slab of chestnut oak for a couple of reasons. First, it was already cut and I did not have to drag the chainsaw out and fight the weeds and humidity. Second, it was bone dry and needed turning before it became unusable. Finally, it is hard wood, and this particular piece started out at 16" by 2"+, a nice medium sized piece to start with.

I started the piece out on the supplied faceplate, which is a very heavy and well made 4" diameter chunk of steel with plenty of holes in it for holding wood. Just to be complete, I brought the tailstock up - well, I almost brought the tailstock up. Every lathe has its idiosyncrasies - that is why we call them that - and one of this lathe's peculiar features is that the tailstock, while having enormous travel, does not quite meet the center of the headstock with the supplied centers, or as I found out, with a skinny slab screwed to a faceplate. To those who are wondering, there is a 2" gap. This gap was quickly removed by installing my Oneway live center. I don't know that I really needed it, but I like to start rough pieces out with the tailstock for support, even when screwed to a faceplate. Call me a sissy if you like.

I started out on the slow speed range, which runs from 0-382 rpm or something like that. I had lots of torque, but I got a little impatient, so I switched the belt over to the high range, which is 0-2400 or thereabouts. I can see where the low range is going to be very nice for really big pieces that are unbalanced, but I think the thing is going to spend most of its time on the high range. There is a little loss of torque at the lower speeds on the high range, but that is not a real issue, and I may be overly sensitive to that, being used to the Poolewood and its direct drive.

I got the plate rounded and shaped on the bottom, and was just getting ready to reverse it when a good friend of mine, who I had not seen in months arrived. While he is a hobby turner, he has to work for a living, so we have not seen much of one another for a while. He had some time to see the new lathe, and after a while insisted that I continue to turn. This was probably not a good idea on my part, since I was jabbering away while cutting, and as a result, went quite a bit thinner than I intended at the bottom of the piece. I came very near to going through. Now, very near sounds a lot like veneer, and that is about what I have left on the bottom of this plate! I told my buddy that it was not a problem, and that I would just tell people it was art and supposed to be that way! It has some cracks in it which will lend integrity to support of the story if not to the integrity of the bowl. ;)

So by now you are probably thinking, "Is he going to show us a picture or not!?!"


Here is the lathe with the plate almost finished. Shavings are not much, but hey, it's a plate! I have some 24" walnut waiting to be bowls, but I need to get a coring tool post for my KM tool before that happens, because I am not turning walnut into shavings!


Here is a closeup of the plate. Nothing spectacular, but it is going to end up being pretty. As I type, finish is drying up in the shop, and if all goes well, it will end up looking like it is about 100 years old. More on that in a different post. The finished size is 15 1/2" x 1 1/2".

Overall, this is a very solid lathe. I need to spend some time with it to learn it better, but it is a very good fit for my shop, especially since it fits in my shop! Some initial impressions: The speed ranges are okay. I could wish for an intermediate one, but I can live with what it has. I have turned on just about every lathe on the market, and I can stall them all with an aggressive cut with the exception of my Poolewood. I can stall it too, but it has to be a [I][B]real[/B][/I] aggressive cut, or a real big outboard piece at a fairly slow speed. The tailstock has a bit of wobble in it, but it also sticks out well over a foot, and I had it stuck in a rough piece. It is dead on center when the proper centers are installed to bring it up to where they meet. I got the lathe to rock just a little bit, but I think the biggest reason for that is my stupid concrete floor, which was poured by drunken sailors. I will be fussing with it a bit, and may go as far as to (gasp!) bolt it to the floor to keep it from moving. The controls are simple, straightforward, and belt changes are relatively fast compared to some other lathes I have used. The machine is whisper quiet, the loudest noise coming from the fan that cools the electronics in the speed controller.

Working around the end is pure luxury. I have the same capability on the Poolewood both outboard and at the end, since its headstock pivots and slides the whole length of the bed, but in either case the setup time is nowhere near as fast as on the Vega. Within a matter of seconds I can twirl the lever at the end of the tailstock and it is off and out of the way. It takes about the same amount of time to reinstall it. The locking levers for the tool rest and banjo are very positive and stay where they are put. The tool rest istelf is not a cheesy piece of cast iron (the worst place for cast iron on a lathe in my opinion) but is steel, and formed for close support and comfortable use. Maximum height is 45" with the telescoping legs fully extended, and that is a little low for me, but I am going to leave it as it is. I like 48" for the spindle height, but that is high for most people, and I have a series of boxes for people to stand on when they come to use the Poolewood. Between this one and the Vicmarc, which adjusts from about 35" to 47", I have the whole range about covered. Tall people just have to stoop!

Thaks for taking time to read, and if anyone has any questions, please let me know, and I will be glad to try and answer them.

Bill

Re: Vega plus shavings (pics)

#2

Re: Vega plus shavings (pics)

David Galloway

>Thanks Bill for the details and pictures. You seem satisfied sans a few idiosyncrasies. I am very interested as I have been looking at the VB and the new Powermatic as possible options for a bowl lathe. Keep giving any feedback you can. I know Mark Kauder loves his and I hope to get on it one day. I have turned on the VB and everyone raves about it that has one. I just choke at the price.

Thanks again. I'm real interested in how it works out for you through time.

David

Re: Vega plus shavings (pics)

#3

Redemption

Mark Kauder. Phenix City, AL

>You know, when you recommend something to someone else, there is always this nagging doubt "I may be happy with it, but what will they think". I am glad that you find the Vega satifactory for you as well.

I am so happy that it meets your basic requirements.

Thanks,

Mark

Re: Vega plus shavings (pics)

#4

Re: Redemption

Lee Dale

>Congrulations Bill, I feel the same way Mark. It seems that we both were on the money....Lee

Re: Vega plus shavings (pics)

#5

Re: Vega plus shavings (pics)

Bill Grumbine (Kutztown PA)

>Hi guys

David, I would not even put the idiosyncrasies down as problems or defects, just the difference between one lathe and another. I've been using my Poolewood for six years now, and that is half of my total turning career! When you spend that much time on a single machine, you get used to how it works. Like a lot of other demonstrators and teachers, I get regular opportunities to use different machines, but those are once and done sort of things. Now I have to get used to those little differences in my own shop. It is not going to be a hard thing. As far as the VB 36 goes, I hear it is a very nice machine. I have never turned on one, although I have a standing invitation to do so when I am out towards Pittsburgh. Since my daughter will be attending college out that way, I will be doing it sooner than later I think. But, you could buy two Vegas and keep one for a spare for what a VB would set you back. It may not be as massive, but how often do most of us turn TD sized blanks?

Mark and Lee, this was a great choice, and Mark you especially know my views on personal responsibility. You were good enough to point me in this direction, but I take all the blame myself! I happen to know of two other gentlemen who have Vegas either in their shop or on the way because of my big mouth the day after coming home from John's place. I am pretty sure they will like it too.

Bill