Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Knock down spray booth

Posts

Knock down spray booth

#1

Knock down spray booth

Dominic Greco at home in Richboro, PA

>Hello Everyone,

I found that when it came time to set up my spray equipment most of the time was spent laying down newspaper, or covering up tools in the "blast zone". Once you get the paper set, a breeze, or an errant blast of air could easily mess up your layout.

So this weekend, I decided to make something to make my life a little easier. It's just a simple knock down spray booth, and it cost me $35 to make. All you need is one sheet of 1/4" hardboard, (2) 24" long piano hinges, and some assorted scraps (I used 3/4" plywood).

My garage/shop isn't big enough to hold a dedicated "finishing room" (yet). So this booth had to be easily set up and broken down. It also had to be stored flat against a wall when not in use.

The dimensions are based on the type of projects I spray. Mostly smaller stuff like bowls, vases, peppermills, bottle stoppers, and pens. The booth measures 36" wide x 24" tall x 18" deep. The sides spay out at 12 degrees.


view of booth from the front


spray booth from side

The piano hinges join between the (2) 24" tall x 18" deep sides and the 36" wide x 24" tall back. The sides fold up right against the back for storage.

If you look at the photo, you can see the blue tape inside. This is where I screwed up. I could only buy 30" long piano hinges at Home Depot. My plan was to cut them to fit the sides. However, I cut them 18" instead of 24". So the tape is there to help block the holes!


view of booth from front with top removed

The top and bottom have pieces of plywood edging along the sides and back. Each piece of edging has a 1/4" deep x 1/4" wide rabbit that is sized to receive the sides and back.


corner detail

Once you're down spraying, this whole thing knocks down to an easily stored assembly.


spray booth disassembled and folded up

All told, I think this took about 3 hours to finish. And that was taking my dear sweet time cause' it was so hot out to hurry!

Thanks for viewing.

See ya around,

My ugly mug



Dominic

Re: Knock down spray booth

#2

Re: Knock down spray booth

Sean Troy

>Have you thought about using a lazy susan to access all the way around your turning? Great looking spray setup. I need to start building one also. Sean

Re: Knock down spray booth

#3

Got one already

Dominic Greco in Richboro, PA

>Sean,

Thank you for the compliment.

You wrote:

"Have you thought about using a lazy susan to access all the way around your turning?"

On the recommendation of Mark Kauder and Joel Hunnicutt, I built one of those lazy susan things last year.

But funny you should mention those. Since I usually schedule my spraying so I have several bowls to spray, I wanted to build a couple more. On Friday afternoon I stopped by two of my local woodworking stores looking for lazy susuans. They were both out. But one store said they'd have them next week.

See ya around,

Dominic

Re: Knock down spray booth

#4

Re: Knock down spray booth

woodspinner/ Bill Hale

>Dom

My only concern is that I see no exhaust fan system. The way it looks the fumes and fine spray come right back on you and will increase your exposure.

Consider a couple of med size fans mounted on the sides to ducts to move the spray and fumes away from you.

Good turning and be safe

Bill in Casa Grande, AZ.

Re: Knock down spray booth

#5

That's why

Dominic Greco in Richboro, PA

>

I wear an OSHA certified mask. But thanks for your concern.

Remember, this is a down and dirty, knock down assembly. I wanted to keep it as simple as possible.

BTW, most times I spray with the garage doors open and my shop's ventilation fans going.

Dominic

Re: Knock down spray booth

#6

Re: That's why

John Lucas

>I've seen the same thing done with a furnice style filter on the back and a fan place behind the filter. I don't know if the fan had an explosion proof motor or not. I'm not sure how serious this problem is but it does worry me. I don't have one of the OSHA maskes and a little booth like Dominic showes just makes a huge cloud of airborne finish after spraying a piece or two. Right now I have a fan at my back blowing toward the makeshift booth with a filter in the back but I don't now how truely affective this is. You can still smell the fumes quite a bit but I don't notice the airborn fog anymore. Oh I forgot to say that I place the booth in my doorway so it blows outside and kills my neighbors.

Re: Knock down spray booth

#7

Filter media

Phil Joines Krum, Texas

>MSC carries paint booth filter media. This one is 20 x 20 x 2 for $0.48.

http://www1.mscdirect.com/CGI/NNSRIT?PMAKA=00626754

They also have an odor control activated carbon filter, same size for $23.01

http://www1.mscdirect.com/CGI/NNSRIT?PMAKA=76935709

A combination of the two aught to catch just about all the nasties.

Re: Knock down spray booth

#8

Re: Knock down spray booth

Joe Flemig

>Dominic,

I have to agree with the rest. I used a large cardboard box for my first booth and just got a big cloud of blow-back right into my face. The booth accomplished nothing. Right now, I just spray outside on the lawn.

I would put a fan out the back. There was an article in Fine Woodworking about 2 years ago that explained the mechanics of a good booth. They used a 20" box fan with a furnace filter.

Joe Fleming - San diego