Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Have any of you built your own lathes?

Posts

Have any of you built your own lathes?

#1

Have any of you built your own lathes?

Keith Newton

>I have not been aware of this forum for very long, and don't have much of a feel for who is who here yet. I was wondering if any of you have built your own lathe, and or have made many of your tools.

I built myself a big lathe a couple of years ago, and have the parts ( A 1000 # headstock, and 5 hp motor.) for another, but don't have any need for another.

I have also made a lot of my hollowing tools. Most are kind of large, and ugly but I like the way they work. Do any of you do this and care to compare notes, or do you keep your ideas secret?

Re: Have any of you built your own lathes?

#2

Re: Have any of you built your own lathes?

Jim King

>Keith:

As we are in an area where there are no lathes or tools to buy we make everything and all looks a bit crude but works well.

Re: Have any of you built your own lathes?

#3

Re: Have any of you built your own lathes? *LINK*

Eduardo Sarmiento Hall-Lima Peru

>Well yes I also made my own lathe ,after a Sorbys desing, and is quite a lathe after many others I think this one is good for my type of work

you can see it at my web page under SHOP


artistic woodturning from peru

Re: Have any of you built your own lathes?

#4

Re: Have any of you built your own lathes?

Ken Grunke from SW WI

>Kieth, you mention a 1000 lb headstock--is that formed with concrete by any chance? Someone had posted a concrete lathe either here or on WoW a while back.

I think that's a neat idea--line up all the metal parts (spindle, bed, and tailstock) with temporary braces and plywood forms, then pour concrete around 'em.

food for thought, anyway ;-)

Re: Have any of you built your own lathes?

#5

Re: Have any of you built your own lathes?

Eduardo Sarmiento Hall-Lima Peru

>the only lathe that I heard from that has concrete in the base is the vega lathe

Re: Have any of you built your own lathes?

#6

Concrete Lathe Link *LINK*

Jay in TX

>Eduardo... you stand corrected, or sit if you like cause its probably hot down there ;~)


WC Thread with Link to concrete lathe operator

Re: Have any of you built your own lathes?

#7

how about a poor man's Tormek?

Joseph

>I made this from a bunch of odds and ends...mostly to see if it would work.

Image hosted by Photobucket.com

Total cost was about $4 for a can of paint...the rest of the parts were gleaned from the "stuff-piles" of 3 generations of pack-rats.

I used an OLD hand-cranked sharpening stone that had been gathering dust in my Granpa's garage. To it I added a toilet water supply faucet to drain the basin into a pop bottle, supported in an old ABS pipe. Gramps also had an ancient 1/3 HP motor that I connected to 4 pullies and an arbor tree to slow the 1750 RPM motor to about 80 RPM at stone level (yes, the top pulley is from a clothes line). I also added 4 casters for mobility and an old light switch to turn it on and off.

To my surprise it works great, I can even change the rotation direction of the stone by "twisting" one of the round belts into a figure 8.

I was planning to make a honing support guide, but becuse of the slow speed, I found that freehanding was possible. But time and practice will determine if I eventually add a guide.

Cheers,

Joseph

Re: Have any of you built your own lathes?

#8

Re: how about a poor man's Tormek?

bernie feinerman

>Looks interesting - how about some details

Re: Have any of you built your own lathes?

#9

Sure, what would you like to know?

Joseph

>

Re: Have any of you built your own lathes?

#11

Re: Have any of you built your own lathes?

Bill Weissborn

>For those who have built their own lathe, where did you get things like main spindle, tail-stock, etc. I ask as I am thinking of building a replacement lathe(since I have more time than money or sense). BUT I don't know if I want to just buy replacement parts or have them machined. Not sure there would be much difference in price either way...

Bill W