Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Chechen Bowed Plate

Posts

Chechen Bowed Plate

#1

Chechen Bowed Plate

Jim Shaver - Oakville, Ontario

>Hi,

I must be on a roll, two turnings in less than 3 days!

This is something new I tried, a dished out piece of Chechen. It is about 5 1/2 x 5 1/2" by about 3/4" tall. I chucked it up to my Stronghold and shaped the outside then flipped it to clean us the bowed inside. The challenge was definitely the fine thin cuts you have to make once the material is very thin. With the interrupted cut I this process there really is no safe way to dampen the vibration and the chatter you get on the inside face. So I did resort to my RAS and some aggressive sanding to clean up some of the tool marks.

The finish is oil and then it was Bealled,

take care,

Jim


img

Re: Chechen Bowed Plate

#2

Re: Chechen Bowed Plate

Eduardo Sarmiento Hall-Lima Peru

>Well it sure looks like the huayruro we have here nice turning well done

Re: Chechen Bowed Plate

#3

2nd Chechen Bowed Plate

Jim Shaver - Oakville, Ontario

>Hi,

Here is a second one showing more sap wood..

take care,

Jim


img

Re: Chechen Bowed Plate

#4

Re: Chechen Bowed Plate

Jim Shaver - Oakville, Ontario

>Thanks Ed,

What ever you want to call it is fine with me!!

:-)

take care,

Jim

Re: Chechen Bowed Plate

#5

Re: Chechen Bowed Plate

Ed Kelle

>Nice bowl Jim. I haven't tried a square bowl yet but hope to sometime soon.

Hey, I sand a lot too so I won't tell if you don't ;)

Re: Chechen Bowed Plate

#6

Is it still a turning if you sanded it? :-)

David Propst

>Hey Jim,

Nice square platter thingys. I like 'em. The though thing for me would be to get it initally chucked up dead center, an easy thing for you guys who easily transition from flat to round and back.

Feeling mischievous,

David

(frequently seen digging through the seconds box at the Klingspor WW Shop)

Re: Chechen Bowed Plate

#7

Re: Is it still a turning if you sanded it? :-)

Jim Shaver - Oakville, Ontario

>Hi David,

Yes my 80 Grit Gouge does work, sort of like my sand wedge of turning tools, tons of spin!!

:-)

take care,

Jim

Re: Chechen Bowed Plate

#8

nice!

e

>very cool and very hard to do ... very nice work!

have you had much movement since finishing?

mine have all warped, even though the wood was very dry. and the chatter-marks were almost impossible to remove.

Re: Chechen Bowed Plate

#9

Wonderful!

Mike Schwing from Md.

>This is really nice work Jim! Very subtle slope from the angle pictured, I really like it. Has an Asian flavor to it, and would be great as a set.

Re: Chechen Bowed Plate

#10

dead center

Mike Schwing from Md.

>David, not sure if that was tongue in cheek or not, but dead center chucking these things are a snap. Here's one way

Determine center by drawing the standard X from diagonal corners. Mark it on the side that will become the top of the bowl/plate.

Chuck up a glue block and turn it just barely concave, maybe 1/64th depression center/edge. This will prevent wobble and provide good glue surface at the same time. (some turners will disagree with this and insist it has to be dead flat - whatever works is fine by me) Apply glue of choice (mine is 5 minute epoxy)

Lock the headstock. Bring the tailstock in close. Take the workpiece and put the tailstock center point in the center point you marked on the workpiece earlier. Crank the tailstock to move the workpiece into the glue block. Before it gets tight, but when it is seated, give the workpiece a 1/2 rotation spin by hand, this will ensure it is seated well on the glue block. Crank the tailstock to firm up the glue joint and wait for it to dry. If done correctly it will be damned near impossible to center it better.

(I think you know this next part but it might be new info for others) If your tailstock live center is threaded, you can buy or make a tailstock chuck adapter that will allow you to screw the whole chuck and workpiece onto the tailstock, which can then be used to perfectly center the work on a jamb chuck or vac chuck so that the bottom can be turned and finished. Works great!

Re: Chechen Bowed Plate

#11

Re: dead center

David Propst

>Hey Mike,

I was semi-joking, but your technique tips are appreciated and have been copied to my save file.

Thanks!

David

Re: Chechen Bowed Plate

#12

Re: Chechen Bowed Plate

Tom In Red Deer

>Nice stuff again Jim. I always enjoy looking at your pens and other turnings. Are your flatwork tools feeling lonely yet?

Tom in Red Deer

Re: Chechen Bowed Plate

#13

Re: Chechen Bowed Plate

Jim Shaver - Oakville, Ontario

>Hi Tom,

Thanks for your kind words...my flat work is chugging along no problem, and my pens and turnings are filling in the spaces...It's good to be busy in the shop these days eh!

My best to all out in Red Deer!

take care,

Jim

Re: Chechen Bowed Plate

#14

Re: Wonderful!

Jim Shaver - Oakville, Ontario

>Thanks Mike,

I was thinking the same it's fun eh!! Now let's see, should I carve on it??

Take care,

Jim

Re: Chechen Bowed Plate

#15

Re: nice!

Jim Shaver - Oakville, Ontario

>Hi e,

Mine have been stable , well, for now. the chatter marks were really pronounced, I tried some very light shear cuts with the gouge to clean it up, but the interupted cut was difficult to get just right...I understand what you are saying though...80-120-180-220-320 oil worked out well..

:-)

take care,

Jim

Re: Chechen Bowed Plate

#16

Re: dead center

Jim Shaver - Oakville, Ontario

>Mike, I closed my eyes and guessed....Not!

:-)

They were recessed with a forsner bit of a diameter that fit on my Stronghold chuck.

Take care,

Jim

Re: Chechen Bowed Plate

#17

Re: Chechen Bowed Plate

Jennifer@Indy.USA

>Uh, Jim...don't you have some pens to turn? Hee-hee :)

I totally love these thin plates Jim. What a great way to use up your flatboard scraps! Can't wait to see the Chechen table these came from!

Keep the turnings coming....we love em'!

Jen