Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Cole Jaws

Posts

Cole Jaws

#1

Cole Jaws

Don Emmerling

>I purchased the Cole jaws for a Tekna Tool midi chuck and it works fine, except for one aspect. After turning about 5 bowls to near completion and attempting to affix the bowls in the jaws to finish turn the bottoms, I find that 4 of the 5 bowls would not seat appropriately in the jaws. No matter how I position them not all of the little black bumpers would align around a circle. I could get 2 or 3 to work but the remainder would have to be positioned in the next outer row of screw holes which would not allow centering of the piece. I have looked at the instructions but it does not cover this problem. Any thoughts would be appreciated.

Regards,

Don

Re: Cole Jaws

#2

Re: Cole Jaws

John Lucas

>Don Are you turning your bowls green? They will warp enough to not let all of the bumbers touch the bowl. My other question is, have you taken the inner jaws out? If you have you may have gotten(I'm sure that's not a word) one jaw ofset by a tooth.

If the bowl was green and warped just use as many jaws as you need. If only 4 jaws touch then use a really light touch when cutting the bottom. I also bring up the tailstock and use it when in doubt.

Re: Cole Jaws

#3

Re: Cole Jaws

Mike Schwing from Md.

>I'd like to echo John's comments and add one - stretch wrap plastic. The kind you get in a roll with a handle at Home Depot or Office Depot. Affix the piece as best possible with the jaws as per directions, then wrap, wrap, wrap the piece onto the jaws with the stretch wrap. You don't need to avoid the area where you will be working, just wrap right over it and before you start turning, use an xacto knife to cut that area away. The stretch wrap will hold that sucker in place better than the best Cole jaw kung fu grip. Don't hold back on the wrap, it is very inexpensive and more is better.

Re: Cole Jaws

#4

Re: Cole Jaws

Carole in VA

>Thanks for the tip, Mike! I have a whole roll of that stuff that I was going to throw in the yard sale bin!

Re: Cole Jaws

#5

Also

Bill Howatt

>I often use the wrap as a safety backup when vacuum chucking just in case I spring a sudden leak.

Bill

Re: Cole Jaws

#6

Re: Cole Jaws

DD

>The stuff you learn on this site is amazing. I've had a roll of that stuff for years. I've rarely used it but now it should go a lot quicker than it has in the past. Thanks for the tip.

Doug Dubowski

Re: Cole Jaws

#7

Re: Cole Jaws

Don Emmerling

>Thanks Mike for your response but that is not quite my problem and perhaps I did not explain it clearly. The bowls I am trying to finish off all are flat with regard to the rim. I expand the chuck jaws and place the bowl over the chuck looking for the row with the best fit, however there is no spot for the bowl where there is room to screw in more than 2 or 3 of the rubber bumpers and 3 will not hold the bowl effectively. There seems to be no alignment of bumpers that will yield a good fit all the way around the edge of the bowl.

Hopefully I am explaining this clearly.

Regards, Don

Re: Cole Jaws

#8

Re: Cole Jaws

ben d

>Don''

I had the same problem with a super nova chuck and had the same suprise with the first bowl I turned.

Got on the teknatool web site and e-mailed my complaint and their reply approved by Teknatool was to drill and tap another hole in between each present hole and there is enough room to do this. They also told me to send to their distributor here in the US and he would do the fix at no charge. I did and he fixed and sent back and so far I have been able to chuck what I need to.

Sorry I cannot find his web address but bet if you e-mail Teknatool they will come back with the same reply.

Hope this helps.

Re: Cole Jaws

#9

Re: Cole Jaws

Mike Schwing from Md.

>Sorry, I understood that but didn't address it specifically because I thought that John had done as well or better than I could have. It sounds like the rims of your bowls, or at least the one in question, have warped out of round. I don't use my cole jaws anymore (vac chuck) but the only times I can recall this happening were from oddly shaped workpieces. Still - I agree, 2 or 3 bumpers is not good, but if you can at least get it to hold still and be centered with 2 or 3, wrapping it in stretch plastic will secure it extremely well. I would have no fear of finishing the bottom of such a piece if I had wrapped it up good and tight.

The only caveot to this is that stretch plastic can really exert some serious force, so be careful with a very thin and delicate piece, but the same applies for the cole jaw bumpers in this case.

A picture of what you're having trouble with would go a long way here..

Re: Cole Jaws

#10

Re: Cole Jaws

robert davis

>forget the cole jaws and make yourself a longworth chuck.button positions are infinite

Re: Cole Jaws

#11

Re: Cole Jaws

Barry Irby

>Don, Are you sure you have your chuck and jaws assembles correctly? If you get the sliders in the chuck in the wrong order, they will be out of alignment. Same is true if you put the jaws on in the wrong order. Try closing the chuck all the way and see if it closes up as it should with all the jaws tight and neatly aligned.

I have a Midi chuck which is dedicated to the Cole jaws. The restraining pin that prevents the sliders/jaws from falling out got lost years ago, not exactly on purpose, but its gone. The jaws Will now slide further, making it possible to grip most any size. If I unscrew the chuck too far, they fall out and its a little tricky putting them back. I did not know Technatool would drill me an extra set of holes. Hmmmm? Is it Tim Geist?

Incidentally, I made my self a set of hooks that I use in place of the rubber stoppers. Man, are they an improvement! They expand the reach to about fifteen inches and grip about ten times as well as the stoppers. They have a second set of holes that is "off-set" to vary the grip range. I should patent them and license them to Technatool.

Re: Cole Jaws

#12

Re: Longworth Chuck *LINK*

William Duffield, on the Cohansey

>To make your own Longworth Chuck, use these instructions in the WoodCentral Turning Archives:

Making a Longworth Chuck, thanks to Garrett.