Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Hollow Vessel

Posts

Hollow Vessel

#1

Hollow Vessel

Steve Roxberg

>I finished a hollow vessel last night that has a 1 1/2 inch wide opening and is six inches deep.

All previous attempts at a hollow form with a small opening (1 1/2 for me right now) have turned into open vases after I blew out the opening so sanding and finishing the inside weren't a problem.

How do I sand the interior? The walls are about 1/8 " think and pretty darn consistent.

How do I finish, or do I finish the inside.

It's Maple so I will be using tung oil followed by poly for the exterior.

Any tips would be appreciated.

Re: Hollow Vessel

#2

Re: Hollow Vessel

tdaniel

>If you cannot get inside just fill it with rocks and tape the opening and let the lathe rotate for a few hours at slow speed. The sliding, tumbling rocks will smooth up the inside.

TD

Re: Hollow Vessel

#3

Re: Hollow Vessel

Jennifer@Indy.USA

>Now that is a great idea TD. I always agonize over the inside of my hollows that I can't get my fingers into in order to sand. I will have to try that. Thanks for the tip!

Jen

Re: Hollow Vessel

#4

Re: Hollow Vessel

Bill Crommett

>DUHH ! Talk about not too bright . As an old rock hound pebble tumbler it never crossed my mind that the tumbling trick would work on wood. I don't know whether to blame it on old age or just general density. Thanks TD for the reminder.

Re: Hollow Vessel

#5

Will only work if.....

tdaniel

>your lathe speed will go down to about 100 rpm or so; faster than that the rocks won't slide around but will just be pinned against the side of the vessel. The tip came to me from Phil Johnson in our club.

TD

Re: Hollow Vessel

#6

Re: Will only work if.....

Steve Roxberg

>Well you can rule that out, my Jet 1236 will only go down to 500.

Does anyone apply finish in there? I would think you would want to to balance the surfaces. The wood is fairly dry, but not totally as you would expect from any large block of wood.

Re: Hollow Vessel

#7

Re: Will only work if.....

Darrin

>What about using sand?

Re: Hollow Vessel

#8

Re: Hollow Vessel

Tony Dentino - NJ

>What kind of rocks work best? Rough gravel, smooth stones?

Tony

Re: Hollow Vessel

#9

One idea...

Peter Teubel

>Turn a collar from contrasting wood and make the opening 1/2" or less. That way the inside is AUTOMATICALLY sanded to 12000 and smooth as glass. ;)

Re: Hollow Vessel

#10

Re: Can be done ...

Ed Thomas, Leaside (Toronto) Ontario

>You can get your 1236 below 100 rpm if you happen to have a small motor lying around, say1/4 hp. It is fairly simple to clamp it to your stand ... remove the back cover of the Jet motor, exchange the plastic cooling fan for an 8" pulley ... drive from the small motor with a 1.5" pulley. Ratio is 5 1/3:1.

Re: Hollow Vessel

#11

I use granite gravel but any hard rock will do

tdaniel

>coarse sand should work but I have not tried that.

TD

Re: Hollow Vessel

#12

Re: Hollow Vessel

Bob R

>How slow is slow?

How large or small???????????

Bob R

West Mac Turning

Re: Hollow Vessel

#13

Re: One idea...

Sean Troy

>

Re: Hollow Vessel

#14

Re: Will only work if.....

RK in Milw

>I do sand the inside of my hollow vessels. I came up with my own device and you can either make one yourself or purchase one from me for $25. I call it the ACME Sand-o-Matic.

I use this sander on a Sorby Multi-tip tool, or even better, on a Sorby Hollowmaster ( the swan necked tool). The sander can be rotated to fit the approximate contour of the vessel interior as needed. The sander also works well for sanding undercut bowls.

1. The dense rubber foam is from a sanding block that comes in a Micromesh kit.

2. Use the teardrop shaped scraper blade from the Sorby Multi-tip tool as a template and trace it on the foam using a ball point pen. Be sure to trace the hole for the mounting screw.

3. Cut the outside shape out of the foam block using a band saw, jig saw or whatever. The sides need to be perpendicular to the face and as smooth as possible.

4. Coat the shaped foam block with thin superglue. This provides a smooth surface for the self adhesive velcro hook material.

5. Using a brad point drill, drill a 1/2inch hole where you marked the screw hole. This is the hole for the nylon bushing.

6.The bushing is 1/2inch o.d. x 3/16inch i.d.x 1inch long. I sanded mine to a length that matches the thickness of the foam - 7/8 or 3/4 inch long.

7. Rough up the outside of the nylon bushing and superglue it into the 1/2 inch hole in the foam shape.

8. Apply a trimmed length of self adhesive velcro hook material to the outside perimeter of your sander.

A 2 inch dia. velcro backed sanding disc cut in half works well as an inexpensive sanding media.

There you have it. Hope this helps. Feedback appreciated.


img

Re: Hollow Vessel

#15

Acme Sand-O-Matic

Rick in Lincoln

>Very ingenious. Simple to make, I have all the materials at hand, just the right size. Making it the same size as the teardrop cutter makes it work even better. Well done. Mine will be made shortly. A seriously great tip.

Re: Hollow Vessel

#16

Simple Sanding Jig

David Propst

>Hi Steve,

To sand the inside of the opening I use the jig pictured below. This was not my idea, but I cannot remember where I got it...probably here.

Turn one end of a 1/2" dowel down so that it will chuck into your drill; on the other end, bandsaw a cross, with the kerf about 3/4" deep; cut two strips of cloth sandpaper about 1/2" x 3" and loop each around two opposite points of the cross in the end of the dowell; insert in the hollow form and sand away! I use 120 or 180. The goal is not to make a finish quality surface, but just to smooth the rough spots.

Mine is long enough I can hold the drill with one hand and the other hand can hold the dowel to control it.

David


img