Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Wood bracelets

Posts

Wood bracelets

#1

Wood bracelets

echo8287

>My daughter saw some wood bracelets at the mall. She came home and wanted me to make her some on the lathe. I made one and it turned out ok,I was wondering if there was a better way to mount it on the lathe. I turned it between centers and cut it down to as far as I dared go. Then sanded the outside and the inside curves. Then I cut it all the down until it almost came off.Then I cut some thin strips of sandpaper and put them between my chuck jaws and the wood.(inside chuck)Trued up the center and sanded the inside. Is there a better way of doing this? I'm a rookie at this stuff. David

Re: Wood bracelets

#2

Re: Wood bracelets

adrien

>You could mount the separated bracelet on a spigot of wood placed in the chuck, same as people do with boxes. If the spigot is tapered, that would allow you to get to half the inside as well as the outside of the bracelet

Re: Wood bracelets

#3

Sanding - finishing inside a bracelet

Fred in NC

>OK, one dangerous contraption right out of my secret machine shop ...

I have made a few bracelets. I have hole saws to cut 2-1/2" to 3" holes in a square piece. Then I cut the corners off in the bandsaw. To turn the outside I mount the piece on a mandrel. I turned the mandrels out of construction grade pine, about 3-1/2 square by 5". In one end I drilled a 7/8" hole, and used a tap to thread to 1"-8 to fit my spindle.

With the mandrel blank on the spindle, and the live center on the other end, I just turned to a good sliding fit for each size bracelet. Then (off the lathe) I made two crossed cuts from the tailstock end for about 2-1/2". This is the same idea as a collet. The tailstock will expand the mandrel slightly to hold the bracelet in place.

Finishing the inside was a brain teaser. I wanted to round the inside of the bracelet slightly to make it more comfortable. I do not have any suitable chuck jaws, so.... the result can be seen below. The reason for the wood is twofold: It can be adjusted to the shape of different bracelets, and the wood parts are easily replaceable.

NOTE: I do not get my fingers near that spinning nightmare. A piece of sanding sponge is attached to a stick, just like a turning tool.


img

Re: Wood bracelets

#4

Re: Sanding - finishing inside a bracelet

John K Jordan

>Great contraption - I want to make one! I wonder if some kind of stretchy sock or something (rubber glove, thin innertube, glued-up neoprene wet suit material?) around the outside of the jaws might help in case of an accidental slip.

JKJ in East TN

Re: Wood bracelets

#5

Contraption

Fred in NC

>John, what kind of chuck do you have? The one pictured is a Supernova II. Email me if you like, just change the AT...

Re: Wood bracelets

#6

Safety

Fred in NC

>John, that is one of the reasons for the wood parts, they can be rounded, and will break a lot easier than the metal. A spongy rubber sock could be added easily.

I considered making it out of wood, but the chucking pressure would break the legs. Plastic was also an option, but was too flexible. The wood parts of course could be made from UHMW poly if wanted.

The inside of the wood parts (the channels) were trued with the lathe running to make sure the bracelet would center properly.

The next run of bracelets will be made, I hope, with a Rose Engine. Right now I am working on the spindle part of the Rose Engine. The spindle will have 1-8 threads so my chucks and faceplates will fit.

Re: Wood bracelets

#7

Re: Contraption

John K Jordan

>I also use the supernovas and I can see from the photo how to make one. Looks pretty simple. Thanks!

JKJ in East TN

Re: Wood bracelets

#8

Re: Safety

Barry Irby

>What about trying a sleeve out of a "No Hub" plumbing fitting? Looks like a 3" one might work. Its a Neoprene gasket that come inside a stainless sleeve with two hose clamps. Fernco also makes a bunch of soft rubber plumbing fittings. Might find the right size there.

That about taking some pieces of wood blocks and cutting a rabbet in them that would fit the angles on the jaws and mount them so that the jaws are flush with the back side. Then turn the outside to a cylinder and hollow the inside and cut the groove for the bracelet. That is, make a set of wooden jaws that resemble standard steel jaws.

I just don't want to have to start calling Fred "Tripp" because he only has three fingers on one hand.