Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Non- laser HF turners question

Posts

Non- laser HF turners question

#1

Steven Antonucci

Non- laser HF turners question

steve antonucci

>For those of us attempting to do deep HF turning, how do you go about measuring wall thickness? I have a few caliper sets, but the foot always ends up thick. Seems that a need for greater accuracy is increased the thinner you go.

Please post your homemade calipers or measuring solutions for small opening, thin wall, deep HF turning.

Steve

Re: Non- laser HF turners question

#2

Brad Vietje

Big Calipers

Brad Vietje

>Steve,

No digital camera these days, but I usually just use larger sized calipers. I don't yet have the Kel McNaughton calipers, but I like them. I like the way these measure both sidewall and base thicknss. Sometimes I do set up the laser rig to measure the bottom third or so, especially on larger, or taller pieces, even if they were hollowed with hand-held tools.

I used to try for really thin walls all the way down (sort of as a challange, and because David Ellsworth can, so why not ?), but a few pieces crash landed in a gallery because they were so light they weren't very stable (small-footed, too). I've taken to making them thinner up top, but leaving the base a little thicker for greater stability. Your larger Cherry urn below is probably just about right in my book -- 1/8" or so, then gradually thickening up to 1/4" to 5/16" at the foot. You may not agree (or may have other design priorities), but I like a little mass in the foot. (I also have a tendency to make round-bottom pieces these days, making a little basal mass even more desirable).

Safe spinning,

Brad Vietje

Thetford, VT

Re: Non- laser HF turners question

#3

Re: Non- laser HF turners question

GeeSeaWhy

>I eventually gave in and built a laser rig following Bruce Hoover's plans in American Woodturner (Spring 2003 issue). I don't have a captive system, I do all my hollowing freehand. It's difficult to use the laser on the tool I'm using for hollowing, it gets in the way too much. But attached to a second tool, it works well as a caliper - even in areas of the HF that are hard to get at. You just have to keep adjusting the laser to be sure you are measuring perpendicular to the wall.

Graeme

Re: Non- laser HF turners question

#4

Re: Non- laser HF turners question

Bill Grumbine (Kutztown PA)

>Hi Steve

I have several David Ellsworth style calipers hanging on my wall of various lengths. They are nothing more than a piece of heavy gauge copper wire. Ten gauge works well. Bend the wire around into a circle, and make it so that there is a gap of an inch, or some other quantity grater than the thickness of the wall you are going to measure. Stick it in the form, measure the distance between the outside wall and the outer part of the wire, and do the math to get the wall thickness. You do need a light touch so as not to bend the wire while it is in the form, or you may have to say bad words shortly thereafter.

Bill

Re: Non- laser HF turners question

#5

.035 drill bit

Terry Daniel

>Steve, I drill a couple of tiny holes in the base where my calipers can't reach. I just stick a small piece of wire or pipe cleaner through the hole and watch for it inside using my flexshaft flashlight to see it. When done the sanding dust fills the hole.

TD

Re: Non- laser HF turners question

#6

Non laser technique for bottom HF vessels

Donna Banfield

>Steve, if you're only trying to get a measurement on the bottom of the hollow form, this low tech tool might work. I cannot claim this, and I'm sure others use this, but it came with the lathe when I bought it from the original owner. He was doing deep hollow forms with the Dennis Stewart Arm Brace.

Using a long piece of metal rod, aluminum, steel, whatever is thin but won't flex, afix a long piece of 1/2" by 1/2" thin wood, by drilling a hole in the center of the wood. You're essentially making a 'T' or cross. The hole that you drill should be large enough to allow this wood cross piece to slide easily up and down the metal rod.

Use wing nuts on either side of the wood, but slipped onto the rod to keep the wood 'T' in place once you get it to the position that you want it to stay.

_________|___________ Wood

|

| Metal Rod

|

|

|

To measure place the rod into the hollow form until the tip hits the bottom of the form. Then slide the wood up until it rests on the opening of your hollow form. Then use a large square edge to place on the outside of your hollow form at the base. Then pull the metal rod out of the form, and place it perpendicular to the hollow form, just like it was before, only this time the rod is OUTSIDE the form. By comparing where the end of the rod is to the square edge, you can see how much or how little room you have left at the bottom of your vessel.

I wish I could post a photo of the tool, and how to use it, but for the life of me, I cannot seem to get the sizing right to post anything here on Woodcentral. I've been able to successfully post to WoW, but not here! And that's after help from Woodcentral members. If you'd like, I can send it to you directly if you send me an email telling me it's o.k. Or I can post to WoW.

Donna