Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Plywood Vase

Posts

Plywood Vase

#1

Plywood Vase

Bill Kram

>Here is my first PIC posting, it was a contest entry at our Portsmouth, NH woodworkers club. The club is primarily a flat work group but they tolerate one or two turners. The contest rules were simple & straight forward, take a 6 foot x 4 inch x ¾ inch board & make something with it.

Being a turner, I started to plan a round object. Circular reasoning I suppose. My concept proceeded in this manner. The 4 inch dimension would limit the diameter so I planed to use some segments. I wanted to KISS (keep it simple stupid), keep the piece count down. Also, I chose Baltic ply (actually stock birch ply from HD) to provide some surface pattern. The body rings have only 4 segments per layer. By choosing a vase form, some of the base & neck sections could be cut from a 4 inch square. The body diameter is 6" W x 9 H. There was some more stock left so I made a lid 2" H with one 6 segment layer. Total piece count is 38.

What most pleased me about this effort was the stimulation of creative juices because of the design constraint.

It forces focus & some structure to thinking about forms. A sort of "form follows function kind of thinking."

Appreciate any comments.


img

Re: Plywood Vase

#2

Re: Plywood Vase

tek-Brunswick, Ohio

>I think it turned out great! Did you have to sharpen your tools more often? There is a lot of glue to turn there and it's abrasive.

Re: Plywood Vase

#3

Come on over

Jack Savona

>What a distinctive and eye-catching look, Bill.

How about bringing it to our Portsmouth woodTURNERS group at Woodcraft? We'd REALLY appreciate seeing it first hand.

Jack Savona

Re: Plywood Vase

#4

Re: Plywood Vase

john lucas

>Bill Very Nice. I like the pattern you worked with. I've only turned plywood a few times and enjoyed the patterns. Now I see why I need to get back to it.

Re: Plywood Vase

#5

Re: Plywood Vase

John K Jordan

>Very nice. I sometimes think the look of strong grain on segmented pieces is distracting, but I like the symmetry of your piece, especially as combined with the top and base treatment.

I was looking at pictures of some of Rude Osolnik's plywood pieces just the other day and thinking of the potential there. I'd like to try my hand at that someday. Do you use any special techniques for turning plywood?

Thanks for sharing.

JKJ in East TN

Re: Plywood Vase

#6

Re: Plywood Vase

Ed Kelle

>Very nice. Was there a lot of difficulty with tearout at all? Harder to hollow?

Re: Plywood Vase

#7

Re: Plywood Vase

Bill Kram

>Yes, plywood has its peculiarities. The wood is soft but the glue lines are hard & abrasive. From my limited experience with a few of these pieces I find frequent sharpening necessary. But, sanding is easier than with solid wood. Tearout is a problem & occasional voids do occur. Some filling with sawdust & CA is usually needed. Finishing is straightforward, these were done with oil & have a low gloss.

I have mixed feelings about the strong grain patterns. They can be very interesting, but sometimes a little too strong. Can you see the smiley face at the shoulder? Using solid wood in combination with the ply gives a nice balanced effect. Also, I have seen Steve Gleasner's use of semi transparent stain on his plywood. I plan to try that on my next piece.

Re: Plywood Vase

#8

Re: Plywood Vase

Ed Kelle

>Hi Bill, yes the smiley is nice. I'm just wondering how come it appears that the ply has curves to it. is that due to the way you glued it up? I will have to try a ply piece sometime.

I'll keep my eyes open for when you post some dyed pieces. Nice work!