New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

American Chestnut Bowl fuming before & after pics

Posts

American Chestnut Bowl fuming before & after pics

#1

American Chestnut Bowl fuming before & after pics

Craig Daymon

>Here is a rehash of my American Chestnut fuming experience, cut and pasted from previous posts with the addition of before and after photos. The bowl is about 9.25" in diameter by 3.5" deep and was turned on a JET Mini (non-variable speed).

I finished turning the American Chestnut bowl. I did some reading on the American Chestnut and as the blight of the tree in the U.S. was key to the downfall of the leather tanning industry in the U.S., I thought fuming the bowl was an appropriate finish technique for the project as both relate to its high tannin content.

The bowl is sitting in a styrofoam container along with 2 small cups of household ammonia. It will be in there for about 14 hours before coming out to air for about another 12 hours and getting the first coat of finish. It is upside-down on top of some packing foam and weighted down. The weight is sitting on top of a piece of MDF wit 4 toothpicks in it to minimize surfacce contact. Hopefully, this will result in a fumed outside and an non-fumed inside (and rim). Dark outside, light inside.

Heat will speed the fuming process, but I think the best way to achieve this would be to bring a light into an cooler through the drain hole and rubber cork around the wire. I have a 40 gallon cooler that I have considered rigging with such a set up but the results I have gotten have been sufficient to produce the desired effect.

The bowl is out of the cooler now and, unfortunately, the inverting of the bowl did not produce the desired effect. The whole bowl is fumed a chocolate brown, MAYBE a LITTLE darker inside than out, but not much. This could be for several reasons, 1) Not enough weight to produce a tight seal against the foam, 2) Not using an appropriate material to achieve the seal, 3) Unseen cracks allowing the fumes to penetrate into the bowl (there are 2 knots in the bowl that might have through cracks). Too bad, it would have been an excellent effect.

One side note, the chestnut reacted very quickly to the woodburning tool when signing, so my usually sloppy signature is especially so on this piece.

Here are the before and after pictures, with one coat of Waterlox applied after the fuming.

-Craig


img

Re: American Chestnut Bowl fuming before & after pics

#2

Well done!

Dominic Greco at home in Richboro, PA

>Craig,

I like the way this turned out! From the color imparted by the fuming to the design features, and overall proportions of the bowl. Very nicely done!

About the problems you experienced while wood burning your signature. It's not sloppy, it's just your "style". :>)

Here's a little trick I picked up (I might have told you this one before). Sign your name with an HB lead pencil first, then trace over it with the wood burning tool. If you screw up with the pencil, you can always sand it off!

See ya around

Dominic

Re: American Chestnut Bowl fuming before & after pics

#3

Re: American Chestnut Bowl fuming before & after p

Barry Turner

>I like the fuming. Nice bowl. Long live Jet mini's!

Re: American Chestnut Bowl fuming before & after pics

#4

Re: American Chestnut Bowl fuming before & after p

Jim D.

>Craig,

I really like the results you got with this. If I am reading your post right you only fumed the bowl for 14 hours?

Jim D.

Re: American Chestnut Bowl fuming before & after pics

#5

Re: American Chestnut Bowl fuming before & after p

Craig Daymon

>Yep, that's right. It went in the cooler at 10AM and came out at Midnight. The most important thing I have found with fuming, especially when using household ammonia, is an air tight container.

I watched David Marks fume a piece on HGTV one time where he made a simple plastic tent and used commercial ammonia. The results he got (White Oak) were nowhere near what I have gotten with household ammonia and I think he fumed for about 8 hours. With a good, air-tight container, commercial ammonia should do the trick in only a few hours, but it is VERY DANGEROUS to work with. Stick with household and just give it more time.

Tannin content of the wood being fumed plays an important part. Chestnut is VERY rich in tannin, therefore it responds very quickly. White Oak is typically very rich as well, but probably not near as much as Chestnut.

When a piece first comes out, it is rather dull in color and is still being affected by fumes absorbed. Applying finish makes the deep color shine. I have read that the best way to monitor the color is to take several sample sticks from the same stock as the wood to be fumed and put them in the container, pulling out pieces after different exposure times and applying a finish coat to get an idea what the results would be. Personally, I just put the piece in and give it at least 12 hours.

-Craig

P.S. Also remember that you can fume other woods (aging cherry) by giving the wood a brush coat of tannic acid. I think it is available as a powder to mix with water from the grocery store, or you can just brew a strong pot of tea and brush it on. Check out the Sept/Oct 1997 issue of Fine Woodworking for a great article on fuming with ammonia. Even though he doesn't use household ammonia and even recommends against using it because he doesn't believe it to be strong enough, everything else applies. (His tent could be more air tight.) The article is available in PDF form for about $4.