New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Curved tool rest for bowls

Posts

Curved tool rest for bowls

#1

Curved tool rest for bowls

Pat Mulligan

>I have some deep bowls to finish soon and I was wondering how many bowl turners use curved rests.I've been doing just fine with the straight rest up till now but I got into that bigger is better thing and the reach is just too far.I was thinking about the oneway rest.Thanks in advance for any help. Pat

Re: Curved tool rest for bowls

#2

Re: Curved tool rest for bowls

Barry Irby

>I have the standard straight 12" rest that came with the lathe. Started looking for a bigger curved rest. Talked to the owner of the local Woodcraft who is also a turner. He talked my out of it, saying that they did not work well and were not worth the money. Later, I bought a "homemade" one from a fellow club member. 1" steel round stock for both the post and the rest with it extended probably ten inches on the left. I'm' not happy with it. I think it has introduced a number of problems. It has too much reach and tends to chatter. It may be that my banjo is simply not sturdy enough for such a long rest. I am thinking of trying one that is about two inches shorter (would reach the bottom of an 8" deep bowl.) I do use it some with it backed away and raised above center for shear scraping with a very light cut, but I think even that would be better if the flex and chatter were reduced. Should have listened to the guy at Woodcraft.

Re: Curved tool rest for bowls

#3

Brian McKearney

Re: Curved tool rest for bowls

Brian McKearney

>I got the Oneway interior curved tool rest last Christmas and I'm happy with it. It allows me to cut the entire interior surface of a large bowl (~15") in one sweep without extending the cutting edge too far beyond the tool rest. I'll probably get the exterior curved rest soon. I think that the curved rest helps with larger bowls.

Brian

Re: Curved tool rest for bowls

#4

Re: Curved tool rest for bowls *LINK*

Mark Mandell - Gone Round In Jersey

>Pat,

Bought one from Bill Kuhlemeyer at Seahorse Custom [see link] dead nuts 90, 1" bar, no vibration. Helps much for large bowls. Not so large that I can do a 15" bowl in a single cut; think that size would vibrate and chatter.

Mark


http://members.aol.com/seahorsecustfab/about_seahorse.html

Re: Curved tool rest for bowls

#5

Re: Curved tool rest for bowls

Chris Andrew

>I have both the inside and outside curved tool rests from Oneway. I use them all the time on bowls ranging from 6 inches up to 17 inches. I can't imagine being without them!

Re: Curved tool rest for bowls

#6

Re: Curved tool rest for bowls

Jim Ketron

>Made my own 1" cold roll. Love them!


img

Re: Curved tool rest for bowls

#7

Re: Curved tool rest for bowls

George Tyler,Louisa, VA

>I too make my own straight rests. How do you bend yours into a curved shape?? Hot or cold?

Thanks, George

Re: Curved tool rest for bowls

#8

Re: Curved tool rest for bowls

Donna Banfield

>I have the curved tool rests made by Woodcraft, the small and larger ine. These are the kind that screw onto the right diameter post. I have always experienced chatter at the very end of both of these curved rests. But still used them, primarily when I was used the round scrapers to clean up the bottoms of bowls.

About a year ago, I acquired the outboard for the Oneway, and some very large blanks. A few months ago I got some 30" plus black walnut, that I roughed out. I had trouble with the first blank because the tool was hanging about 6 or more inches off the rest at the very bottom of the bowl. Normally not a problem for me, or most people, but when the blank you're working on is HUGE, as it comes around, there's a tremendou amount of torque coming down on your gouge, making it pretty scary to turn.

So, I knew that when I was going to finish that blank, I would need the curved tool rests. They arrived a couple weeks ago, and I remeber saying to my husband, "they don't look very beefy" for Oneway rests (not as beefy as the tool rest that comes with the outboard, anyway). I was concerned that I was going to get chatter at the very end of this rest, just like my other ones.

Boy was I wrong! No chatter or vibration at all! So, I'll be replacing my old curved toolrests with Oneway toolrests as soon as I can come up with the $$. Here's hoping for a successful selling season this fall!