New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Storing/Using CA glue question.

Posts

Storing/Using CA glue question.

#1

Storing/Using CA glue question.

Barry Irby

>I noticed in a post that someone said they stored their CA glue in a closed container with some kitty litter desiccant. I have mine in a drawer in the lathe cabinet. I have noticed that sometimes it will sit for weeks and the little spouts stay open, even with the caps off. Sometimes it plugs itself up. My shop is only heated or cooled when I am in there, so the temperature and humidity vary. As I recall it used to do it when I kept the caps on, also. When I used the accelerator in the spray bottle, I kept it on a shelf above the lathe because it leaked enough that the glue would harden if it were in the same drawer, but with the spray cans, I don't worry about it. It also seems the size of the hole in the tip matters. If the glue drains back out of the tip its better. Is it the humidity that causes the glue to harden in the tip? How do you store your CA to prevent this?

Re: Storing/Using CA glue question.

#2

Re: Storing/Using CA glue question.

Bill Crommett

>My routine is to squeeze the bottle a couple of times in the upright position to be sure that the glue is all sucked down into the bottle, and then I wipe of the spout with a paper towel before putting the cap on.

Re: Storing/Using CA glue question.

#3

Re: Storing/Using CA glue question.

Ken Grunke from SW WI

>CA is an anerobic (spelling?) setting glue, meaning it sets without oxygen. The advice I've heard the most is to leave the cap off and throw it away--then after each use, tap the bottle on a hard surface to shake the glue down from the tip. With the cap off, you need a secure place to keep the bottle so it doesn't tip. Being woodturners, that's not a hard thing to make--just a small mug with a wide base.

Since moisture is an accelerant for CA, it makes sense that high humidity can cause the tip to clog, if it's not emptied after use. But putting the cap back on a wet tip will surely do it.

Re: Storing/Using CA glue question.

#4

Peter Charles Fagg (UK)

Re: Storing/Using CA glue question.

Peter Charles Fagg (UK)

>Barry, like Ken Grunke I leave an air space but keep mine in the cold food store, not the freezer, it seems to extend the shelf life.

Regards Peter.

Re: Storing/Using CA glue question.

#5

Re: Storing/Using CA glue question.

Eaglesc

>I go through lot of it and never put the cap on the bottle.

If I remember to tap it fine, if not I just twist off the hardened glue with a pair of pliers, Ca has a lousy shear stength.

I keep 16 oz bottles in the fridge and refill 2 ounce bottles from that.

All unopened bottles stay in the fridge.

Re: Storing/Using CA glue question.

#6

Re: Storing/Using CA glue question.

John K Jordan

>I put the caps on and store them in a fridge. Before I did this I'd had entire opened bottles harden.

JKJ in East TN

Re: Storing/Using CA glue question.

#7

Re: Storing/Using CA glue question.

Bruce Wiseman

>I put the cap back on then store the stuff upside down. I dill a hole in a peice of scrap about the diameter of the cap and place the glue cap side down into the hole. It keeps the liquid at the bottom which is now the cap end. I think it helps but it is the way I've always done it so maybe it isn't any better than the other suggestions.

Re: Storing/Using CA glue question.

#8

Dick Hines

Re: Storing/Using CA glue question.

Dick Hines

>I toss the caps and place one of those little tips with the pin hole in the end. They give me better control where I put the Ca and if they get pluged up I can just cut a little off the tip with a ulity knife. Just remember to whipe the blade before you retract it or you will glue the blade to the inside of the knife.

Re: Storing/Using CA glue question.

#9

Re: Storing/Using CA glue question.

Bill Buck

>One of the guys here stores CA without caps,open to air, and put them in another container with the small silica things you find in medication bottles. He says it's the moisture that causes CA to harden.

Works for him

BIll