New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Survey, favorite bowl gauge(s)

Posts

Survey, favorite bowl gauge(s)

#1

Survey, favorite bowl gauge(s)

Jorge Castaneda ~ Downeast Maine

>I have been turning bowls lately, some roughing green wood and some finish turning of dry. It seems that roughing green blanks big enough, I can do all of it with the 5/8" Hamlet Ellsworth gauge, for small blanks I use mostly a 1/4" Crown gauge; now for turning the bone dry roughs, I can do the outside with any gouge, but the inside I don't seem to be able to do it with just one gouge, have to switch between several.

Do you have one gouge that does the inside job for you? if so, what size and how it is ground, most of the bowls I am making are 5" - 7" and 11" - 14".

TIA

Jorge

Re: Survey, favorite bowl gauge(s)

#2

Re: Survey, favorite bowl gauge(s)

Verne

>After taking a class from David Ellsworth, I only use "his" gouge for the inside and outside. Too bad I hadn't taken the class before buying some of my other "had to have" tools :-)

Re: Survey, favorite bowl gauge(s)

#3

Re: Survey, favorite bowl gauge(s)

Jorge Castaneda ~ Downeast Maine

>Verne,

Yes for the most part I use his gouge, but in very dry hard wood, sometimes it is not the best tool for me, also in small bawls, that 5/8" gauge is just too big for doing the inside of the bowl.

Jorge

Re: Survey, favorite bowl gauge(s)

#4

Re: Survey, favorite bowl gauge(s)

MP Wall

>I use a P&N 5/8 ground to ellsworth for most of the work and a 3/8 Crown PM ground to ellsworth as a back up and for tighter or smaller places. MP Wall

Re: Survey, favorite bowl gauge(s)

#5

Re: Survey, favorite bowl gauge(s)

Jorge Castaneda ~ Downeast Maine

>Thanks MP

The 3/8" has been calling me for a while, the gap between the 5/8" and the 1/4" is too big, I think I will give it a try.

Thanks again

Jorge

Re: Survey, favorite bowl gauge(s)

#6

Peter Charles Fagg (UK)

Re: Survey, favorite bowl gauge(s)

Peter Charles Fagg (UK)

>Jorge, for all my turning, that is both inside and out, I use a 1/2" Robert Sorby deep flute, ground to 55 degrees.

Regards Peter.

Re: Survey, favorite bowl gauge(s)

#7

Re: Favorite bowl gouge

Mark Mandell - Gone Round In Jersey

>I'm with you, Jorge, the 5/8 Hamlet is my choice for most anything from roughing to shearing. While I use the Ellsworth grind (his jig, etc.), it can be hard to maintain a smooth level surface from the transition in to the center, especially on more closed form bowls. I find it helps to rotate the flute clockwise as I move through the cut, and a relieved bevel (see Russ's section in the Grinds Library) helps as well. David also shows a different grind on the same gouge where instead of the ground-back wings, he does a blunt grind at about 85* and a slight scew with the long side on the left flute. First time I used that one the difference was almost "magical" but it's exactly the same tool; just a different grind.

Mark

Re: Survey, favorite bowl gauge(s)

#8

Re: Survey, favorite bowl gauge(s)

Jorge Castaneda ~ Downeast Maine

>Thank you Peter

Cheers!

Re: Survey, favorite bowl gauge(s)

#9

Re: Favorite bowl gouge

Jorge Castaneda ~ Downeast Maine

>Mark

You hit the nail on the head:

>> it can be hard to maintain a smooth level surface from the transition in to the center, especially on more closed form bowls<< That is exactly where my trouble lays, the blunt grind and the skew you mention, I think I saw once Dave Lancaster using something like that, and everything looks really easy when he is doing it, but not so with Jorge. I will look into that, maybe reground a P&N that I use as a spare when the Hamlet dulls.

Gracias!

Jorge

Re: Survey, favorite bowl gauge(s)

#10

Re: Survey, favorite bowl gauge(s)

Barry Turner

>I just bought a Crown PM 1/2" Gouge with the Ellsworth Grind. My only other bowl gouge is a 3/8" Sorby with a side grind. Although I've had it only about a month, the Ellsworth is already my favorite. I bought the Ellsworth video and have finally sorted outhow to sharpen the Ellsworth on the Wolverine jig. I'm still on the steep side of the learning curve on using the gouge, and trying to learn how to actually make all the cuts shown on the video, but thus far..........I like!

Re: Survey, favorite bowl gauge(s)

#11

Re: Survey, favorite bowl gauge(s)

Jorge Castaneda ~ Downeast Maine

>Thanks Barry,

I have the Ellsworth jig and it is very easy to use, no guessing at all, on the minus side it cannot accept as many shapes as the Wolverine and it oly does what it does, but does it very well, so maybe is a well worth small investment, once when you get the shape, it is a snap to maintain it.

Crown makes really good tools, my first bowl gouge was the 1/4" Crown and looks like it will last me for ever, I like it very much, but for heavy work I use the 5/8' hamlet.

Thanks

Jorge

Re: Survey, favorite bowl gauge(s)

#12

Re: Survey, favorite bowl gauge(s)

Barry Turner

>My Crown PM has a shank diameter of 5/8", so we have very similar gouges.