New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Lathe Spindle Morse Taper Scoring

Posts

Lathe Spindle Morse Taper Scoring

#1

Lathe Spindle Morse Taper Scoring

Roland B. Kuehn

>This the second posting of this message, the first was on the general message board, but my son advised me to post it on the turning message board so here it is. I have a new 3520A Powermatic lathe that now has a scored internal Morse #2 Taper from a drive center that evidently turned in it. It took a bit to drive the center out. What is the best way to clean up this score? Thanks to those who answered my posting on the general message board.

Bo

Re: Lathe Spindle Morse Taper Scoring

#2

Re: Lathe Spindle Morse Taper Scoring *LINK*

Mark Mandell - Gone Round In Jersey

>Roland,

A #2 Morse taper Hand reamer will resolve your problem. Check with a "friendly" local machine shop and you may be able to borrow one for a day. With the lathe OFF, the reamer is GENTLY inserted into the taper and then GENTLY rotated with light hand pressure and a open-end or crescent wrench. Take 2 revolutions, remove the reamer, clean off and shaved metal, reinsert, and repeat several times until the reamer makes even contact in the taper without "catching" when turned. Stress "gently" here because you can really screw up your taper by overdoing this.

Once you have the spindle taper restored, you must carefully clean and de-burr the drive center and any other appliance you plan to use. Failure to do this will recreate your current problem all over again because the defect in one will transfer to the other.

You can prevent this in the future buy cleaning both tapers and the inserts (tailstock too) before each use, making sure that any burrs, scratches, dirt (including wood dust), and grit are removed. Packard sells a urethane rubber item called the "TaperMate" that looks just like the reamer and will remove dirt from the female tapers which is probably what caused your problem to begin with.

If you can't borrow a reamer from a shop (local turning clubs often have them as well), ENCO (link) sells the #2 for about $26 plus shipping. Thing is, if you're careful about keeping things clean, you'll never need the reamer again. Wicked thing that looks cool on the tool board though |;-}}}

Note again that the reamer is only for repairs, not for routine cleaning the tapers; overuse will reshape the tapers and throw your machine's alignment off until you go buy a New Spindle and quill (not a good thing).


ENCO -Reamer

Re: Lathe Spindle Morse Taper Scoring

#3

Re: Lathe Spindle Morse Taper Scoring

Fred in NC

>I agree with Mark. One little fact most people don't know about using reamers... they can be easily damaged if ROTATED BACKWARDS. They have precision edges, and they are designed to be rotated ONLY in the cutting direction. So pull the reamer out straight.

Re: Lathe Spindle Morse Taper Scoring

#4

Re: Thanks, Fred

Mark Mandell - Gone Round In Jersey

>Forgot to mention that. Only ones I've used are for clockwise rotation, and, actually, I continue to turn it a little as it's removed.

Mark

Re: Lathe Spindle Morse Taper Scoring

#5

Re: Lathe Spindle Morse Taper Scoring

John Trant (Baltimore/DC corridor)

>Mark is correct if you have a fairly perturbed surface. If the problem is not too bad (such as a single small protrusion), I would selectively and carefully attack the protrusion (dremel or emory cloth) and then smooth the area with oil and emory cloth. If it is a furrow, I would leave it and correct the male tapered center that induced the problem.

John

Re: Lathe Spindle Morse Taper Scoring

#6

Re: PS

Mark Mandell - Gone Round In Jersey

>Roland,

I don't think I made it clear enough that you should not try to use the reamer to "erase" any marks or sctratches on the taper's surface. It is used only to remove any high spots that resulted from the problem. Since part of the defect (score or gall) is a scratch that is cut "below" the original surface of the taper, if you were to continue reaming until that is gone you would have removed a large amount of metal, enlarged the taper, and created a problem for using the drive centers or any other #2 accessory. The idea here is to only remove the slight high spots on either side of the scratch, not to resuface the taper.

Mark

Re: Lathe Spindle Morse Taper Scoring

#7

Thanks Mark

Stuart Johnson

>This same topic was just covered over on WOW and Mark wrote up the first complete description on how to use a reamer. It sounds to me like using it improperly can be very risky and possibly damaging to the lathe and operator.

Re: Lathe Spindle Morse Taper Scoring

#8

Re: Lathe Spindle Morse Taper Scoring

Devon Palmer

>I had the same thing happen to my 3520, withing a week or so of uncrating it. I've since switched to a texas spur drive that threads on to the drive. I wonder if it could somehow be related to the powermatic?

Re: Lathe Spindle Morse Taper Scoring

#9

Re: Getting Better At It

Mark Mandell - Gone Round In Jersey

>Stuart,

It's funny how much can be left out of just giving what you think is simple advice on a board like this. The issues that cropped up on wow just never occurred to me to address (you very well pointed out how much I'd left to assumptions) so I've tried to go over them again to fill gaps. Consequently, when giving directions it seems best to try to think of anything that can go wrong (go wrong, go wong). Then, by the time you put in all the caveats, limits, and warnings to help people avoid mistakes, it looks like you've described something really tricky or dangerous.

Using a taper reamer properly is actually very simple and easy, and takes all of about 2 minutes to do. Writing about how to do it is much harder! Sooner or later I'll get it right |;-}}

Re: Lathe Spindle Morse Taper Scoring

#10

Re: Lathe Spindle Morse Taper Scoring

Roland B. Kuehn

>Devon;

Thanks for your's and everyone else's response. You are the second person who responded (response to my first inquiry on the general message board of July 6 and 7, 2005) that they also had the same probem with their new 3520 lathe, so there must be a problem with the 3520 spindle machining for so many to have this problem. In fact in his response he told me that there was a problem a couple of years ago with 3520's and Powermatic sent reamers out to all owners to correct the problem. I have contacted Powermatic on the probem but have not heard back. This same center drive that I used worked fine in 2 other lathes one old and one mini without problems. Thanks again everyone I will try to keep you up to date on the resolution.

Bo

Re: Lathe Spindle Morse Taper Scoring

#11

Re: Lathe Spindle Morse Taper Scoring

Devon Palmer

>Yeah,

Mine happened around 1/2 inch inside the spindle. I'll call my dealer (Shameless plug: Woodwerks in Columbus/Gahanna, Ohio - best in the state) and get some feedback from them as well.

Warm Regards,

DP, Columbus OH....