New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Show me your latthe setups

Posts

Show me your latthe setups

#1

Show me your latthe setups

Kudzu

>I am getting a new lathe finally and I am staring to think about how I want to lay out my work area. I am fortunate to have a very large shop area in my basement. I have a bowl lathe that I am just finishing up the stand for and I thinking of setting up the two close together so I can easily move from lathe to lathe. Plus I am taking an old kitchen base cabinet and making it into a sharpening station with my grinder, low speed wet grinder, scary sharp station and eventually buffers will go there.

So, show me your set ups!

Re: Show me your latthe setups

#2

Re: Show me your latthe setups 

Anthony Y

>


img

Re: Show me your latthe setups

#4

Re: Show me your latthe setups

JamieDonaldson

>I may have to downsize these photos, but here goes. This is my lathe area, and I will post the view from the other direction.


img

Re: Show me your latthe setups

#5

Re: Show me your latthe setups

JamieDonaldson

>I may have to downsize these photos, but here goes. This is my lathe area, and I will post the view from the other direction.


img

Re: Show me your latthe setups

#6

Re: Show me your latthe setups

John K Jordan

>I like the sharpening station to be within arm's reach of the lathe and the bandsaw not much further. (Not that I have much choice in my current tiny space!) I have shelves to one side with chucks, finishing supplies, etc, racks for sandpaper, calipers, and so on, all within arm's reach. Less often used supplies are in a cabinet about three steps away.

But the most important thing is lighting! I have multiple lights in reflectors - above, in front, and over my shoulder. (Sometimes I want a light at belt buckle height but I haven't figured out how to do that yet.)

JKJ in East TN

Re: Show me your latthe setups

#7

Anthony's Pic is of MY lathe setup!

Ruth Niles

>Seriously, Anthony, that my General, I don't have the exhaust system neatly behind the lathe, it's at my bandsaw and sander. Saved me taking a picture!

Ruth

Re: Show me your latthe setups

#8

Re: Show me your latthe setups

Ruth Niles

>Ok, Jamie, either you turn someplace else or you have a cleaning lady!

Re: Show me your latthe setups

#9

I was thinking the same thing!

Carole in VA

>That shop couldn't possibly be "used". LOL

Re: Show me your latthe setups

#10

Re: Show me your latthe setups

Devon Palmer

>My shop is really small, 10x20, wiht two separate 5x10 wood storage lockers (I rent warehouse space in an artist type commune, although I condsider myself a newbie-craftsman :)

I have my lathe at a slight angle to accomodate wood chip removal and standing at the end. I have a trash can placed at the end to catch "most" of the chips from hollowing.


img

Re: Show me your latthe setups

#11

IIRC

Jay in TX

>that Jamie is only ensuring that the LOHL is satisfied that her automobile's resting spot is well kept... ;~)

Re: Show me your latthe setups

#12

Re: Show me your latthe setups

Devon Palmer

>From the other angle....


img

Re: Show me your latthe setups

#13

Lathesetup - my bad

Devon Palmer

>Lets try THIS one...


img

Re: Show me your latthe setups

#14

Unknown tool?

John Trant (Baltimore/DC corridor)

>For what do you use that big white tool setting behind the lathes? I don't have one of those in my turning shop. ;-)

John

Re: Show me your latthe setups

#15

Re: Show me your latthe setups

Devon Palmer

>This is my favorite thing tho, its a wire bakers rack with Wheels from Lowes, I can roll it to where I'm working, and keep it out of the path of my chip - also makes for easy clean up as I can move it out of the way. Its stable "enough" as long as I don't get crazy with it. I use velcro for holding onto sanding pads and the small container for holding sandpaper as well. I keep all my drives, tools, chuck parts, etc in it. The snap lid container is my "dry box" for glue storage. It has Kitty Litter Dessicant (the crystals) to keep it dry.


img

Re: Show me your latthe setups

#16

Re: Unknown tool?

JamieDonaldson

>That's my wife's Camry tool- for tooling around! I remodeled my shop last year, and for the first time in the 29 yrs. since we built was she able to get her wheels inside, so for Christmas I gave her one of those electric garage door opener thingies! Living large, just like the rich folks!

Re: Show me your latthe setups

#17

Re: Show me your latthe setups

Kudzu

>Thanks guys! This is great. I have picked up a couple of ideas all ready. If you have a good tip or idea I want hear those too. Not just photos.

I am thinking of setting the lathes face to face so I can just turn around and use the other one. I will know better once I get them in the shop. I am also thinking of turning them sideways, not against the wall and leaving space so I can walk around them. This seems like it would be better for cleanup and would be nice if for any reason I need to do work on the lathe.

Re: Show me your latthe setups

#18

Dick Hines

Re: Lathesetup - my bad

Dick Hines

>I don't think any of you guys ever use the lathes. There is no dust and no shavings. Also no wood piled in the corner waiting to be turned. I would have to see a pic of you all turning something before I beleave you really turn there.

Re: Show me your latthe setups

#19

You clean up?

Jack Savona

>

Re: Show me your latthe setups

#20

Re: Lathesetup - my bad

tek-Brunswick, Ohio

>Why don't you build a platform? Standing on that little step stool must really limit your dancing with the lathe! LOL

Tom

Re: Show me your latthe setups

#21

Re: Show me your latthe setups Huh?!?

Ruth Niles

>" I am also thinking of turning them sideways, not against the wall and leaving space so I can walk around them. This seems like it would be better for cleanup and would be nice if for any reason I need to do work on the lathe."

OK, you are being way too influenced by Jamie's sanitary working conditions..........."IF for any reason I need to do work on the lathe"? Already you're cleaning up more than you're turning!

Kidding, of course, you can clean all you want. Don't pay any attention to me.

Re: Show me your latthe setups

#22

Re: Show me your latthe setups Huh?!?

Kudzu

>Well after a while the ceilings start getting lower and the lathe starts getting shorter. Finally figured out what was causing that. :-)

Re: Show me your latthe setups

#23

Re: Unknown tool?

Barry Irby

>Get her to open the windows and take the shavings with her.

Re: Show me your latthe setups

#24

Re: Show me your latthe setups

Steve Lewis

>Here is my Set-up. Notice the balast box I built from Dominic Greco's plans posted on the Articles page. Just finished the tool cart. Mounted on wheels, it is very mobile. Steve


img