New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Needle Scaler-revisited

Posts

Needle Scaler-revisited

#1

Needle Scaler-revisited

Jennifer@Indy.USA

>Okay, so I'm driving past Fort Wayne, IN yesterday on the way home, and I decide to take a detour to visit Harbor Freight and "splurge" on the $12.99 needle scaler. I've been wanting to try one of these for texturing. Am I suppose to do anything to the "needles" prior to using this thing? Round them over? I haven't used it yet but thought I might just ask to see if anybody else is "prepping" their needles prior to use?

Thanks for any tips!

Jennifer

Re: Needle Scaler-revisited

#2

Re: Needle Scaler-revisited

Pete Kekel - Kentucky

>The needles should be rounded over to a ball shape that is smooth all around. With the sharp edges and flat surface (as it comes out of the box), the needles will cause torn grain and not give you an evenly textured surface. I didn't understand this until I used it for the first time and had to go back and re-texture several areas holding the gun at different angles to flatten all the rough ridges. With a smooth ball shape on the end of the needle the texturing is much easier and more uniform.

Re: Needle Scaler-revisited

#3

Re: Needle Scaler-revisited

Two Ton Tommy

>I use the $50 dollar HF needle scaler and don't know much about the $12.99 one but if it is like the one I use the 19 needles need to have the edges rounded over a little. I did it on a belt sander. It is real easy to do. If you don't my experience is that it tears the wood and makes jagged indentures. Also, my experience is you get very good results if you duct tape the needles tightly together. This eliminates that one wondering needle that will tear the wood. It gives you a wonderful stippled effect. My best advise is to experiment on like peices of wood before you use it on your turned object. I think you will have fun with it.

Re: Needle Scaler-revisited

#4

Thank you....

Jennifer@Indy.USA

>I thought that made sense....I'll round them over first. Thanks for the tips!

Jen

Re: Needle Scaler-revisited

#5

Re: Needle Scaler-revisited

Jim Shaver, Oakville Ontario

>Hi Jennifer,

You are starting to scare me...............

:-)

Take care,

Jim

Re: Needle Scaler-revisited

#6

Re: Needle Scaler-revisited

Dale Cook

>I have a couple of them that I've taken apart to round to different degrees of sharpness.I also double up a rubber band to keep them together,then you can squeeze them together to get into tight areas.

Re: Needle Scaler-revisited

#7

Re: Needle Scaler-revisited

Bob Elliott

>Jennifer,

Are you sure that the one you bought is a stand alone unit? The $67 unit is quite long with the long "needles" and the $12.99 version has short needles with four set screws that make it appear to be an accessory item to fit on another air tool.

According to their web site, they describe the $12.99 unit as follows, "Turn your air hammer into a needle scaler. Remove weld flux, rust, scale, paint, cement, and other residues from irregular surfaces. Can be used with our Central Pneumatic air impact hammer (Item 04842), Central Pneumatic long barrel air impact hammer (Item 00574) and other impact hammers with threaded barrels accepting .401'' shanks. Replaceable 3mm needles."

Re: Needle Scaler-revisited

#8

Re: Needle Scaler-revisited

Jennifer@Indy.USA

>Hi Bob,

Yes, that's the one I bought. It fits onto my air hammer. I hope it wasn't a waste of $$. Have yet to test it out.

Jen

Re: Needle Scaler-revisited

#9

Re: Needle Scaler-revisited

Bob Elliott

>Jen,

Well good, you are all set! Let us know how it works.

A few members from our club were set to go for the $12.99 unit until they realized it was an add on to another tool.

Last I heard one of the guys started to contemplate the smaller, more expensive Sioux ($149), haven't heard whether he bought one.