New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Wet Sanding Questions

Posts

Wet Sanding Questions

#1

Wet Sanding Questions

TomW in SouthJersey

>I have a black walnut bowl that is down to a little less than 1/4 think ?? 10" diameter. There is a lot of grain tearoutor voids? And it doesn't look like dry sanding is going to improve things much. I've tried power sanding also.

Is this when wet sanding will help fill the voids? All my tools are sharp (as best as I am able).

If I wet sand should I use water or an oil or something else to lubricate the paper?

I can post pictures if that would help.

Tom Wright

Re: Wet Sanding Questions

#2

Thinned BLO

Dave Smith, Longview, WA

>Hi Tom,

I have had good luck sanding with thinned linseed oil. I use trps which is much better than mineral spirits. Keep the paper wet and slow down the lathe to reduce slinging of the slurry.

Good luck.

Dave Smith

Walls and ceiling splattered with walnut slurry in Longview, WA.

Re: Wet Sanding Questions

#3

Brad Vietje

Re: Thinned BLO

Brad Vietje

>Tom,

Other oils will work, too; sometimes I use mineral oil (paraffin oil), if the eventual finish will be a penetrating oil like Watco, Urethane Oil, etc..., or if your eventual finish will be an oil/beeswax finish a la Raffan. If you use BLO, just remember that even though it smells so nice and natural, it can and will burn your house down if you aren't careful with any rags or paper towels used in the process.

Safe spinning,

Brad Vietje

Thetford, VT

Re: Wet Sanding Questions

#4

Re: Wet Sanding Questions

Mac

>Hi Tom, I wet sand with Watco oil often.The slurry makes a great grain filler.Try starting out by brushing the wood with a foam brush full of oil,soak it down good.Then hit it with 4oo grit wet or dry paper,after the slurry starts to set up a bit,wipe it off in a circular pattern with some cloth and let it set a day or so,then do the same again only use 600 wet or dry.Continue till it suits you and when completely dry, buff it up to satin sheen.....

Re: Wet Sanding Questions

#5

Re: Thinned BLO

TomW in SouthJersey

>I don't have any BLO handy but I do have Watco Danish oil and mineral oil. If I use mineral oil can I apply Danish or Tung oil later for the finish?

Still sanding with 150 grit. But its looking better.

Tom

Re: Wet Sanding Questions

#6

Shear scrape.....

Wally Dickerman

>I suggest that the first step in removing end-grain tearout is to shear scrape. Properly done, shear scraping should remove all or nearly all damaged wood, making sanding much easier. Using oil or wax along with the shear scraping helps. You should be able to find info on shear scraping in tha archives.

Be aware that using oil for sanding will darken the walnut considerabley. I suggest using a soft wax, such as Johnson's paste wax.

Wally

Re: Wet Sanding Questions

#7

Brad Vietje

Re: Thinned BLO

Brad Vietje

>I have used mineral oil followed by a finishing oil without problem, however, you could also use Watco for the sanding (or the shear scraping Wally favors).

Safe spinning,

Brad Vietje

Thetford, VT

Re: Wet Sanding Questions

#8

Re: Shear scrape.....

John Lucas

>I've gone so far as to use a curve cabinet scraper to remove really stubborn torn grain. It can be tough to blend in the are sometimes but usually works out.

I usually only use the sandpaper slurry method to fill grain but it would work quite well to fill some smaller torn grain. I use Tung oil simply because I have some.

Re: Wet Sanding Questions

#9

Re: Shear scrape.....

TomW in SouthJersey

>My shear scraping skils are not where they should be. I bought a Sorby MultiTool and it worked very well and I was learning some shear scraping skills. But the edge has gone dull and I'm having a hard time getting it to work as well as it did when new. I was using my bowl gouge for shear scraping as I observed on Bill G's DVD. But I'm having trouble getting it into the inside bend of the bowl.

I wet sanded with water then mineral oil. It did darken the grain considerably but so far I like the look. The torn grain is almost gone. I'm waiting for it to dry to do some fine sanding.

As always I appreciate the advice.

Tom Wright

Re: Wet Sanding Questions

#10

Re: Wet Sanding Questions

Don Henthorn

>I have used about everything one can think of, even Behr floor sealer. Worked great.

Re: Wet Sanding Questions

#11

Re: Don's website

TomW in SouthJersey

>Don - If you don't mind would you please post your website. I remember seeing it once and being very impressed with your work. I'd like to see it again but beware I DO try to copy objects that I am impressed with. If I remember correctly the finishes on your work was outstanding.

Tom Wright

Re: Wet Sanding Questions

#12

Don't let Dave kid you

Charlie Anderson in Southern Maryland

>He has the cleanest shop I've ever seen! Well, except for Schwings, but he's OC.

Re: Wet Sanding Questions

#13

Re: Don's website

Don Henthorn

>users2.ev1.net/~henthorn