New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

cheap jet mini

Posts

cheap jet mini

#1

cheap jet mini

John Lucas

>Well fans the Jet Mini I got for $129 is not perfect. In fact you can't turn anything on it. The motor runs and the variable speed works but there isn't any torque on the motor. didn't think to check that. I measured 25volts min and 75 max on the output of the drive. I haven't had a chance to check anything else. I have another DC controller and motor for another lathe so I can try that and see if it's the motor or the controller.

Worst case scenario, I'll put the Vega DC motor and controller under the lathe. If the cost of repairing either one is low enough I may try that option. I knew it was too good to be true.

Re: cheap jet mini

#2

Re: cheap jet mini

RonZ

>If it looks too good to be true, it usually is. =o)

You can always break it down and sell it for parts.

Re: cheap jet mini

#3

Re: cheap jet mini

Ron in Drums PA

>Did you check the belts?

Re: cheap jet mini

#4

Re: cheap jet mini

Fred in NC

>The voltage may or may not be the problem. Hard to tell what voltages the motor is supposed to work at.

Does the motor turn faster when you turn the knob?

Does the motor itself seem to have torque?

Is the belt loose (not tensioned) ?

Pulley setscrew loose ?

I would check all those.

I have modified my Jet Mini, non-VS with the Vega motor, and it is a dream to run! Plenty of torque at any speed. The controller that comes with the Vega motor is PWM based, not voltage, and has feedback from the motor, so it will increase the current to maintain the speed. If you try to stall it, you will feel the power surge.

Hope you can make it work.

Re: cheap jet mini

#5

Re: cheap jet mini

John Lucas

>Fred

I didn't have a chance yesterday to really check it out. The belt was tight but I didn't think about the setscrew. It does vary in speed. You can grap the handwheel and stop in low or high speed. I'll have a little more time to look at it tonight but not much. Won't have time to try hooking up the other controller or motor until late in the week.

I'm not concerned. I have enough other stuff laying around the shop to make a working lathe out of this one and it will still be a bargain.

Re: cheap jet mini

#6

Re: Thanks For The Update

Mark Mandell - Gone Round In Jersey

>I was just about to run down to the diner and demand my Free Lunch!

Seriously, hope it works out. |;-}}}

Mark

Re: cheap jet mini

#7

Re: Thanks For The Update

John Lucas

>I thought I was getting a free lunch but all I got was spam. fortunately on my budget I'm used to eating spam. Fried with an Egg and toast goes down pretty well.

Re: cheap jet mini

#8

Want a bed extension?

Carole in VA

>Don't know where you are located but I got one you can have. I can't pack it up and ship it though.

Re: cheap jet mini

#9

Re: cheap jet mini

Don Evans

>Not to worry John, I love these type challenges. You cannot loss on this one. If you decide it's more than you want to bite off, I'll take it off your hands for the price you paid for it.

I've been wanting a little lathe and as we are moving and I've got to build a new shop it will be good time to tackle it while I'm waiting.

Don

Note to Carole: I may be interested in that extension if John want to part with it.

Don

Re: cheap jet mini

#10

Re: cheap jet mini

old griz

>OK, I here about modifying the Jet Mini with a Vega motor and controller... I have a nonVS Mini and would like to do something like that...

How do you go about it and where do you get the parts and what is the cost...

Right now I basically use it mostly for buffing and small stuff because I also have a Jet 1236...

Thanks for any input...

Re: cheap jet mini

#11

Re: cheap jet mini

Carole in VA

>If you are where you can pick it up, it's yours.

Re: cheap jet mini

#12

Re: cheap jet mini

John Lucas

>I would have to look through my notes to see where I got the information. I think possibly Mark kauder first published some info but don't remember for sure. I have about 5 pages of notes I got off the web. I used it to build a slow speed motor for work. Then I bought another motor and controller to put on my Nova mini lathe but moved and it's still in the box. John

Re: cheap jet mini

#13

Re: cheap jet mini

Mark Kauder. Phenix City, AL

>The good news: Here is the shortcut to my article.

The bad news: The motors are no longer available from Vega.

The OK news: This will basically work with any VS motor.

Mark