New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

OUR TURNING PROCESS

Posts

OUR TURNING PROCESS

#1

OUR TURNING PROCESS

Jim King

>In response to Kens question about the process we use for our turnings , it is as follows. The process we use is quite simple. The following photos will give a step by step description. I would have liked to have shown the same piece from start to finish but the rough turned and boiled piece in the photos wont be dry for a couple of days as it was boiled yesterday.´ You can be sure I will be posting this blank in a few days when finished as we have just found this species and it is a dead ringer for Macasser Ebony. One of our people borrowed a chain saw from us to chop up a tree that has been laying in his yard for a few years and this is what it was.

Photo 1: Cutting the square blank into somewhat near round for mounting on the lathe.

Photo 2: Rough turning the outside of the blank to an approximate shape desired.

Photo 3: Rough turning the inside of the piece to obtain approximately a ¾ to 1 inch wall thickness.

Photo 4: Boiling the rough turned blanks for 3 to 4 hours and letting them cool over night in the water or they will crack if taken out hot. They do get quite nasty looking from the boiling but it is less than skin deep.

Photo 5: Drying the rough turned blanks in full sun flipping them every hour or so for maximum 3 days until bone dry.

Photo 6: After finishing turning and sanding to 1000 and applying the floor use polyurethane the pieces are wet sanded on the lathe with soap and water with 1000 grit after letting the polyurethane dry for at least a couple of days.

Photo 7: After sanding the pieces are buffed with a car buffing compound on the lathe, very wet or you can burn the finish. Applied and buffed with cotton rags.

Photo 8: Final thing is a coat of car wax or good floor wax and buffed with cotton rags again on the lathe.

The photos on the lathe look as if the lathe is not turning but is was and the camera incredibly caught the piece as if it was standing still.


img

Re: OUR TURNING PROCESS

#2

Re: OUR TURNING PROCESS

Carole in VA

>Man, that first pic on the table saw gives me the willies! How do you do the bottoms of your bowls after the rest has been finished?

Re: OUR TURNING PROCESS

#3

Re: OUR TURNING PROCESS

Jim King

>Carole: We use a parting tool made from a machete and part the bowl from the face plate which does a very smooth job and then we either sand and finish the bottom or glue a velvet bottom to it. I bet you will want to know where you can buy a machete.


img

Re: OUR TURNING PROCESS

#4

Re: OUR TURNING PROCESS

Ed Kelle

>Holy cow, that is some parting tool.

Did you ever get that branding iron to stamp your name?

Re: OUR TURNING PROCESS

#5

Re: OUR TURNING PROCESS

Bob R WestMac Turning

>Very good info. What speed when you are buffing?

Bob R

Re: OUR TURNING PROCESS

#6

Re: OUR TURNING PROCESS

Jim King

>Ed: I am expecting it in a couple of weeks when some friends are coming down from Canada.

Re: OUR TURNING PROCESS

#7

Re: OUR TURNING PROCESS

Jim King

>Bob: I have no idea what speed our lathe is. We only have one speed and it is quite fast.

Re: OUR TURNING PROCESS

#8

Re: OUR TURNING PROCESS

ken chase

>Jim:

This is fascinating. I'm most grateful for the info.

I just got my buffing system and have one more question.

Which of the three buffers do you use when substituting

car polish?

Thanks

Re: OUR TURNING PROCESS

#9

Re: OUR TURNING PROCESS

Mike Schwing from Md.

>Thanks for the pics Jim. I'm with Carole, that picture of the hand held blank on the table saw is scarier than a picture of Hillary Clinton in a nightie. I was going to ask why you don't use a bandsaw but then remembered that I nearly cut a finger in half with one...

How many of you guys still have all of your fingers?

Re: OUR TURNING PROCESS

#10

Re: OUR TURNING PROCESS

Jim King

>Ken: All we use is shredded cotton rags for buffing and waxing.

Re: OUR TURNING PROCESS

#11

Re: OUR TURNING PROCESS

Jim King

>Mike: We all have all our fingers believe it or not. Our band saw is not big enough for most of the blanks we turn and the table saw is real quick.

Re: OUR TURNING PROCESS

#12

Re: OUR TURNING PROCESS

tek-Brunswick, Ohio

>Jim, We in the United States concentrate way too much on having the best tools and a better lathe than the next guy. You remind us that turning is really in the hand and body movements, the eye, and most importantly in the mind and attitude of the turner. Thanks for makeing me humble and making me think.

Tom

Re: OUR TURNING PROCESS

#13

Re: OUR TURNING PROCESS

Carole in VA

>And you take those huge semi-round blanks and mount them on a one-speed (fast)lathe???? No face shields, no eye protection...yikes!

Re: OUR TURNING PROCESS

#14

Re: OUR TURNING PROCESS

Michael Stadulis, in Gloucester County, NJ

>Hi Jim,

How do you chuch the completed pieces for subsequent buffings?

Mike

Re: OUR TURNING PROCESS

#15

My thoughts exactly, Tom!

Ruth Niles

>

Re: OUR TURNING PROCESS

#16

Re: OUR TURNING PROCESS

Jim King

>Mike: We dont turn the bowls off the face plate until they need no more buffing. We just remove the screws and let the pieces dry and go thru the stages until they have the finish we want and then part them from the scrap.

Re: OUR TURNING PROCESS

#17

Re: OUR TURNING PROCESS

Ron in Drums PA

>Interesting post Jim

What do your bottoms look like when they are rady for sale?