New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Dissolving hot melt glue (how to?)

Posts

Dissolving hot melt glue (how to?)

#1

Dissolving hot melt glue (how to?)

Mike Schwing from Md.

>I messed up an expensive 1" ball shaped carbide carving burr by carving off a glue block I thought I had secured with epoxy. Turned out I used hot melt glue and the burr melted the glue and it got all over the burr, effectively ruining it. I have tried all of the common carbide bit cleaning techniques with zero success. Wire brush, acetone, etc.. no luck at all.

I could heat it up with a torch or one a stove but the reality of that method is that it won't drip off all of the glue - there are thousands of nooks and crannies. Thought if I could somehow dissolve it instead that might be the ticket.

I have not tried a denatured alcohol soak yet but will today. I don't think this will work though.

Any suggestions? Thx.

Re: Dissolving hot melt glue (how to?)

#2

Re: Dissolving hot melt glue (how to?)

John K Jordan

>I don't know a solvent, but I think I'd try a heat gun to soften the glue followed by a wire brush to get it out of the nooks.

JKJ in East TN

Re: Dissolving hot melt glue (how to?)

#3

Re: Dissolving hot melt glue (how to?)

Bob Arnold

>I've heard of counter top installers using alcohol to disolve the hot melt glue they use to adhere clamping blocks to solid surface countertops.

Re: Dissolving hot melt glue (how to?)

#4

Freeze it

Sam Simpson

>Hi Y'all,

Mike, I don't know the chemical makeup of your glue. It is probably not a suspended resin. Instead it is probably a true thermoreactive resin without additives. So the best solvent I can think of would be paint stripper. But I have little faith that solvents will work well. Instead I think I have a better idea. Freeze it! The glue will become brittle and when you chuck it up and hit some wood with it the chances are very good that the glue will all chip off.

Regards Sam Simpson

Re: Dissolving hot melt glue (how to?)

#5

Re: Dissolving hot melt glue (how to?)

Mark Kauder. Phenix City, AL

>Mike,

If all else fails, Burn it off with your torch until it nothing but charcoal. The temp should not get high enough to affect the carbide. Many of the the makers of many of the new carbide burrs recommend this as the way to clear a clogged burr.

Mark

Re: Dissolving hot melt glue (how to?)

#6

Re: Dissolving hot melt glue (how to?)

Don Henthorn

>How about a pressure washer?

Re: Dissolving hot melt glue (how to?)

#7

Re: Dissolving hot melt glue (how to?)

Steve Mushinski

>I think I might be able to help you out Mike. While at Arrowmont in the spring a gentleman from Texas show us that to desolve to remove hot melt glue use CA - accelerator. I did not try it as I have not used hot melt for these type of things yet. I did see how after you spray it on the item that was being turned came right off the lathe no problem. Hope this works for you! Steve

Re: Dissolving hot melt glue (how to?)

#8

Re: Dissolving hot melt glue (how to?)

Mac

>Mike, Propane torch. Wont hurt the burr, burn it all off.Do it all the time.....

Re: Dissolving hot melt glue (how to?)

#9

Did you try......

W.C. Turner

>dipping it into boiling water?

Re: Dissolving hot melt glue (how to?)

#10

Re: Dissolving hot melt glue (how to?)

Greg Jensen

>Hot melt glue comes off with most solvents. Laquer Thinner, Acetone, Xylene.