New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Logo Plates

Posts

Logo Plates

#1

Logo Plates

tek-Brunswick, Ohio

>Some of you may remember, that plates with logos on them is one of the things I like to turn. Mostly I have been making ones with military logos on them. I ran out of the clear label sheets I was using and went to Office Max for more. They were out of the full size clear labels I was using. I found another Avery product that will work. It's called Avery Clear Sticker Project Paper. Avery # 4383. The only difference I can see is they use a different adhesive. I find this product easier to apply to the wood. Here is an example of a plate for those of you that haven't seen them.

Tom


img

Re: Logo Plates

#2

Re: Logo Plates

Arch

>Hi Tom,

Thanks for your post & pic. My wife belongs to a group of ex U.S. Navy & Marine women who meet for lunch regularly. (now come on you guys, WW2, not the Spanish-American) I have inserted fouled anchor uniform buttons into wine bottle stoppers & coasters for gifts & prizes. Your platter is quite attractive and would be a nice change.

Do you have a web site or could you expand a bit re suggestions & techniques here or by email?

Plagiary _is a compliment, isn't it? Anyway it's not a copy if it's not done as well as yours. :)

Best, Arch

Re: Logo Plates

#3

Re: Logo Plates

Wayne Leach

>Very nice!!! I also would like to know more about the details of your process as it might help me with putting digital images into my turning???

Hope you can share some information.

Best regards,

Wayne

Re: Logo Plates

#4

Peter Charles Fagg (UK)

Re: Logo Plates

Peter Charles Fagg (UK)

>Following the comments of others, this is something that could be popular in the UK. As Arch asked is there a website with further information available?

Regards Peter.

Re: Logo Plates

#5

Re: Logo Plates

Don Emmerling

>LEt me join the chorus for a job well done. I to would like to know more about the different logos available and the process for affixing them.

Great job,

regards

don

Re: Logo Plates

#6

Re: Logo Plates

Bob R WestMac Turning

>Great work

Add me to the applause of of your work.

HOW DO YOU YOU DO IT.

Its GREAT.....

Bob R

Re: Logo Plates

#7

Must be a trade secret :))

Carole in VA

>

Re: Logo Plates

#8

Logo directions (long) *LINK*

tek-Brunswick, Ohio

>I did a show this weekend and didn’t have the time to answer questions until now. Unfortunately the hot weather and the fact that this was a first time show kept the customers away.

I’m sorry but I don’t have a website yet. The Logos are something I just worked out on my own by experimenting. Actually the first time I used clear labels was to make a wooden puzzle for my then 2 yr old niece. I tried different ways to transfer images to wood and this method seemed to work out best for me. I tried the Iron on T-shirt transfer that you can print on the computer and those wrinkled. I tried Avery clear labels and they worked. Now I found Avery Clear Sticker Paper ( Avery # 4383) and that seems to lay down easier. I use a Canon I 960-inkjet printer, my earlier printer was an Epson 660 and that worked well also.

Here are a few things I found out by trial and error. The picture or graphics work best if they have large blocks of color and not a lot of fine detail. The areas that are normally white in an image will be clear on the clear paper and show the wood grain the most. The wood grain will also show through the colored areas of the image, but not as well. I like a light colored wood with a tight grain. If there is a lot of detail in the picture or too much contrast in the grain the final product looks too busy .The grain pattern and the picture interfere with each other in that case. I’m using Hard Maple for most of the platters now. I turn and finish sand the platters and apply a coat of lacquer based sanding sealer. Then sand the sealer and let the plates sit at least a day before applying the labels. That is to make sure most of the lacquer thinner has evaporated. I make the labels up on the computer. I size them about an 1/8 of an inch in diameter smaller than the recess on the plate. First I print the Logo on plain paper. I cut them out with scissors and test fit them. If it looks like a good fit I repeat the process on the clear stock. Make sue the ink is dry before you handle the labels. I lay the label on the plate and try to find the best grain orientation. Usually I try to run the grain strait up and down. When I have the label where I like it, I hold the left edge down so the label can’t shift. I peel off the backing off of the right side. I press the now sticky side down. Then I peel the backing off of the rest of the label and press that down. I try to work out any air bubbles as I lay it down. After I’m sure the label is on where I want it and there are no air bubbles I finish the plate with spray lacquer. I used shellac instead of lacquer on some earlier plates and that worked also. Whichever you use spray the finish, use a light first coat and let it set before spraying additional coats. I did a web search to find the military logos. I used Adobe Photoshop Elements to do any adjustments I needed on the images. I use a printing program called Q-Image to print them. I’ve used Q-Image for several years now and find it convenient for my printing needs. I select the custom print size option and type in the dimensions of the print I want. Q-Image is available from http://www.ddisoftware.com/qimage. I’m not affiliated just a happy customer.

I hope this helps. You can e-mail me also.

Tom


http://www.ddisoftware.com/qimage