New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Chainsaw Sharpening Question

Posts

Chainsaw Sharpening Question

#1

Chainsaw Sharpening Question

Tom Colligan, Peoria

>I'd like to try sharpening my chains but I'm not sure what jig to purchase. The Stihl dealer is recommending a Stihl bench jig that costs $159.

Is this the one to buy or is there a better one being made?

Is there a nationwide dealer that is a good place to buy from over this local lawnmower store?

And has anyone tried this and given up as it's too difficult to do correctly? Tia, Tom.

Re: Chainsaw Sharpening Question

#2

Re: Chainsaw Sharpening Question

Carole in VA

>Tom, I freehand mine with just a file. No jig yet but I have looked at the Lee Valley one. Cuts fine so far with just freehanding. I certainly can't see $159 for a benchtop jig unless you are doing a LOT of sharpening! I get the files for a buck fifty each and stick them in a shop turned handle. I have the stones for sharpening with my Dremel but have not tried it yet. If you do a search you will find a whole thread on chainsaws and sharpening. I think someone (maybe Terry?) went into great detail on the sharpening process.

Re: Chainsaw Sharpening Question

#3

Re: Chainsaw Sharpening Question *LINK*

adrien

>http://www.stihlusa.com/chainsaws/accessories.html

is a good starting point to look at the equipment. I should think, if you are just starting out, that a couple of files and a guide would be a good way to begin. To invest big bucks in sharpening equipment before you've gotten familiar with the saw seems premature.

Stihl also has a $10 DVD covering safety, proper use etc. ($5 cost, $5 ship)


http://www.stihlusa.com/chainsaws/accessories.html

Re: Chainsaw Sharpening Question

#4

Re: Chainsaw Sharpening Question *LINK*

Scott Crumpton

>I use an Eze-lap chansaw sharpener in a battery operated dremel tool. The google search below will find both the manufacturer and a retailer in the first several hits. Regardless of the hand method you use to sharpen, unless you're real good at sharpening both sides of the chain consistantly you'll need to have the chain put on a grinder every now and then just to true it up and reset the cutting depth. I usually have this done once or twice and by then it's time to toss the chain.


http://www.google.com/search?q=eze-lap+chain

Re: Chainsaw Sharpening Question

#5

Steven Antonucci

Freehand Dremel sharpening

steve antonucci

>If you are going to freehand with a file, why not freehand with a Dremel? With a file,you need to maintain angles while pushing the file. With a Dremel, you only need to touch the chain at the right angle, and the dremel does the rest.

It's way faster, and in my experience, produces a way sharper chain. (I just did one last night- 5 mins.)

Steve

Re: Chainsaw Sharpening Question

#7

Re: Caution

Mark Mandell - Gone Round In Jersey

>Jim (and all),

I bought the HF $70 deal last year. Had gotten 12-15 sharpenings out of it when the switch circuit board went bad. Called service in May and was informed the new board was $13 plus shipping. "Ok, send me one." " Sorry, but they're on back order until at least August, but we're not sure when they'll come in." "Well, can I put a dpdt line switch in as a temp until the board comes in?" "Sorry, sir, but because of liability, we can't advise you on that question."

Cancelled the parts order, canned the unit, and bought a very good Tecomec (Italian) grinder from Madsen's.

Further note on the HF grinder. It has a tendency to grind the right side cutters shorter than the lefts. If you don't pay close attention to the length of the cutters when you switch sides and readjust the depth gauge, your chain will be sharp but will not cut straight.

M

Re: Chainsaw Sharpening Question

#8

Re: Caution

John K Jordan

>> the switch circuit board went bad...

Can you just fix the circuit board? I've fixed a lot of circuit boards over the years - often it's just a cold solder joint. (I once fixed two automobile airconditioners in one week and they BOTH had cold solder joints!)

What components are on it and how complicated is it - is it a simple contact switch, a "soft" switch, or variable speed control circuit? How do you know it is the circuit board - did the smoke come out?

(That said, I personally prefer a file with a handle but I do use a Dremel with a stone after cutting rocks.)

JKJ in East TN

Re: Chainsaw Sharpening Question

#9

Dremel Bit?

Jennifer@Indy.USA

>Hi Steve, I've been thinking I might want to try the Dremel method. I've seen the Dremel saw sharpening kit. Is that what you are using? If not, which bit are you using to do the sharpening?

Thanks,

Jennifer

Re: Chainsaw Sharpening Question

#10

Re: Circuits

Mark Mandell - Gone Round In Jersey

>Uses two micro switches, one for On, one for Off. Know for sure one went bad.

John,

By the time I drive 1.5 hours each way to a proper electronics store, wait through the counter line, board-in-hand, get the switch (take 2 they're small) then fuss with desoldering, re-soldering, and waiting for something else on the board to blow up, I've wasted more time (gas, money) than the new grinder cost.

My HF Special's now in some mound out in Ohio somewhere.

|;-}}

Re: Chainsaw Sharpening Question

#11

Re: Dremel Bit?

Carole in VA

>Jennifer, they make special stones for most chain sizes. Mine is 3/16". They come 2 to a pack

Re: Chainsaw Sharpening Question

#12

Re: Dremel Bit?

Barry Irby

>I bought the little Dremel attachment for sharpening chain saws. Less than $15 and well worth it. I wish they would elaborate on it and make it more sophisticated. Some "arm" or something to register against the side of the bar to help you keep the cuts level and accurate. Doesn't seem it would take much to make it a lot better. I still like it better than a file.

Re: Chainsaw Sharpening Question

#13

Re: Freehand Dremel sharpening

Jerry Whitaker

>I vote for the Dremel Sharpener..... $8.95 at Walmart and comes with 3 sizes of stones. You need to determine which one you need. Then you can by stones, 2 per pack for about $4.95. It only takes a light touch to sharpen and if you do not abuse the stone, you should be able to use one 15 or 20 times. Be sure and do not use the stone only in one spot....use the whole length of the stone.

Re: Chainsaw Sharpening Question

#14

Re: Chainsaw Sharpening Question

Jerry Whitaker

>I have a new policy: To never buy anything electric from HF.

Re: Chainsaw Sharpening Question

#15

Grinder vs. File

Tom Colligan, Peoria

>Thanks to all for the input. The mechanic/salesman at the Stihl dealership said they use a $500 dedicated grinder for sharpening chains but said "nevertheless, you'll still get a chain sharper with files than you can with a grinder". Tom

Re: Chainsaw Sharpening Question

#16

Pferd Chain Sharp (Link)

Joe T. - Parma, Ohio

>I use the pferd chain sharp to keep my Stihl saw's chain sharp. I give it about 3 swipes per tooth at the end of use and it stays sharp. You can't beat it for under $20. Just make sure you get the one for the depth of your chain. I think it's the best thing out there, and is real easy to use.

http://www.forestapps.com/pferd/pferdtool.htm