New WoodChat!
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Oneway Talon Spindle Lock set screw

Posts

Oneway Talon Spindle Lock set screw

#1

Oneway Talon Spindle Lock set screw

Craig Daymon

>What size is the set screw for the Oneway Talon spindle lock? I'm not certain I ever got one, but it hasn't been an issue (I think) until now. I'm turning a hollowform and the chuck is coming loose. I have the T-handle wrench, just not the set screws. (I think I'll get in the practice of using them all the time now.)

Thanks,

Craig

Re: Oneway Talon Spindle Lock set screw

#2

Re: Oneway Talon Spindle Lock set screw *LINK*

albertabob

>You might try posting that ? on the One-way forum.

They have a resident staff member there to help.

Bob


http://www.oneway.on.ca/forum/logon.php?webtag=FORUM

Re: Oneway Talon Spindle Lock set screw

#3

Re: Oneway Talon Spindle Lock set screw

John Mcalevey

>Take the handle to the hardware store. Go to the boxes that have set screws and find the metric set screw that fits the handle. That will be the size you need. JM

Re: Oneway Talon Spindle Lock set screw

#4

Re: Oneway Talon Spindle Lock set screw

Ed Kelle

>Nope they didn't provide a set screw. And I just checked the manual and unfortunately they don't even mention that you can use a set screw, much less give you a size to go buy one yourself.

Besides searching their site, I guess the best idea is to take the chuck to the local hardware store with you. If you ever find the size, please post it here so I can write it down in my manual. Good luck

Re: Oneway Talon Spindle Lock set screw

#5

Re: Oneway Talon Spindle Lock set screw

Steve Mushinski

>Craig, I think it is 8mm if my memory serves me right. They do not supply them with the chucks anymore as people were complaining that they wrecked the thread on thier spindle. They are only used if you have a oneway lathe or a lathe has a spot to lock down on which isn't threaded. Give them a call on the 1-800 and they might even send them out to you. You never know!

Re: Oneway Talon Spindle Lock set screw

#6

Re: Oneway Talon Spindle Lock set screw

echo8287

>I asked the same question awhile back. The replys stated that they were 8mm and that they would mess up the threads. One nice gentleman suggested using some nylon plastic set screws. I hanen't had any problem with the chuck coming loose so far so I did not try to find any nylon ones,but I thought it was an excellant suggestion. David

Re: Oneway Talon Spindle Lock set screw

#7

Re: Oneway Talon Spindle Lock set screw

Bill Howatt

>Yes, they are metric M8. For the rare time I use them I just put a little bit of brass rod in the hole before inserting the set screw.

Bill

Re: Oneway Talon Spindle Lock set screw

#8

Re: "seat" the chuck......

Ruth Niles

>Craig,

Unless you're turning with the lathe in reverse, the chuck may only be coming loose because you're not "seating" it against the headstock nut. When you screw the chuck on the spindle, just before it stops, give it a flick to seat it. Can't explain it technically, just know it works.

Ruth

Re: Oneway Talon Spindle Lock set screw

#9

Re: "seat" the chuck......

Dennis J. Gooding

>Craig, Ruth has a good point. A further suggestion is to set the deceleration switch on your Oneway to the "slow" position when turning heavy pieces. The braking action may be applying too much reverse torque when you stop. Dennis

Re: Oneway Talon Spindle Lock set screw

#10

Re: "seat" the chuck......

Craig Daymon

>Well, my Oneway has the name, "JET" on it's side and "Mini" in it's name, so it decelerates as it pleases.

Thanks everyone for the help. I know logically it shouldn't be coming loose as the direction of turning should keep it seated, still I'll probably pick up some M8 set screws.

I like the idea of the brass rod to keep from marring my spindle threads. I was looking at McMaster-Carr yesterday and found they have soft tip metric set screws with either plastic (nylon) or brass tips. They are about $2.25 per set screw and I was trying to decide if they were worth it.

Thanks again,

Craig

Re: Oneway Talon Spindle Lock set screw

#11

Whip out the wallet...

tek-Brunswick, Ohio

>Hmmm? $2.25 for a set screw that may save buggering up some good tunings. Now let me think! Post the link and I 'll order some for myself.

Re: Oneway Talon Spindle Lock set screw

#12

Re: Whip out the wallet...

Craig Daymon

>Go to http://www.mcmaster.com and then go to page 2916 of their on-line catalog (or printed catalog if you have one).

Re: Oneway Talon Spindle Lock set screw

#13

thanks

tek-Brunswick, Ohio

>