Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Japanese plane with linde buffing bar

Posts

Japanese plane with linde buffing bar

#1

Japanese plane with linde buffing bar

David Weaver

It took an exceptionally light touch to finish the japanese plane on the yellowcake wheel. Clearance is probably 10-12 degrees at best with a typical setup (iron just over 25 degrees and bed angle on the bottom side at 38). It's much more forgiving to finish just the tip of the edge like this. I haven't looked at this through the scope, but it has the tiniest bright line and nothing more.

The thing that always annoyed me about japanese irons is that as soon as you get yourself a nice amount of clearance, the iron will be chippy (for obvious reasons).

This iron is typical hardness - it's hard, and I'd kind of prefer the lamination thinner and softer as it would have better toughness. We don't have gobs of clear softwoods in abundance to really take advantage of the standard geometry.

AT any rate, diamond hone, washita, linde buff.

I can't tell much of a difference in thinness vs. the stanley, and the obligatory picture at the end shows the shutter speed increased on the phone so that the clarity of the LEDs reflecting on the surface can be seen without just washing out the whole picture.




brand name this or that aside, it's my opinion having had a huge slug of japanese planes that if you can sort through 10 or so used and find one with a very fine carbon steel lamination that's thin with a very supple (easy grinding) wrought backing the thin lamination, that's as close as you can get to japanese plane heavy. This one is a double iron rig that I set up where I removed the wear so that I could see what's going on - and then I lost interest. If I ever do use it regularly, I will hollow grind it some, and if not the soft lamination, part of the fat hard lamination. I guess it takes more skill to get the lamination thin, and you don't see it a whole lot on planes made now. A lot of them are very even with a fat lamination and strike me as being cut from prelaminated material, even if they're not. They just seem like that.

Re: Japanese plane with linde buffing bar

#2

Is this what you mean......

Orlando in So. Fl.

.... when you mentioned that:

I guess it takes more skill to get the lamination thin, and you don't see it a whole lot on planes made now. A lot of them are very even with a fat lamination and strike me as being cut from pre-laminated material, even if they're not. They just seem like that.

Here are pictures of two Tsunesaburo blades. The larger one (70mm) is Blue Steel #1 and is called "Maboroshi" and it translates to "Illusion." I got this one from Stu in the swap for the LN LA Jack. It doesn't need to be tapped out as it wears. The other one is a Suigobo Aogami Super steel 48mm called "Meigoryo (Shiragashi Bakurobori) which Tsunesaburo translates to "Ambiguous" in large planes and "Disappointment" in small planes.

The line on the blades is to reference where to align the chipbreaker to get close to the blade's edge.


Re: Japanese plane with linde buffing bar

#3

Re: Is this what you mean......

David Weaver

Check this picture.

https://auctions.c.yimg.jp/images.auctions.yahoo.co.jp/image/dr000/auc0108/users/7f20848b97309f95813538ac683de75d20ecd23a/i-img1200x1200-1598530292vt1y2p2645206.jpg

Note the thickness of the hardened metal. The listing for this plane says that it's a fake of a blade made by a very famous blacksmith.

The thinner the metal looks from the bevel side, the easier the plane will be to sharpen.

Re: Japanese plane with linde buffing bar

#4

That's clever

Jim Matthews

"The line on the blades is to reference where to align the chipbreaker to get close to the blade's edge."

As with most elegant solutions, it only appears obvious in hindsight.

Where do I send the royalty check?

Kudos

Re: Japanese plane with linde buffing bar

#5

Re: I'm guilty....

Orlando in So. Fl.

Thanks Jim. Not original. I saw it somewhere, just don't remember where. But it did make a lot of sense though. :)

Re: Japanese plane with linde buffing bar

#6

Re: understood......

Orlando in So. Fl.

... it's the bevel side of the blade you were referring to. Interesting that I found that the 70mm Maboroshi's delineation line between the soft/hard metal is a little thicker than the one on the 48mm blade.

I may be wrong, but that "fake" blade looks like it's pretty well made.

Re: Japanese plane with linde buffing bar

#7

Re: understood......

David Weaver

It probably is very well made. A lot of the stones with fake stamps also look by visual characteristics like they would be good stones.