Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

David, Nice work, but for anyone coming late

Posts

David, Nice work, but for anyone coming late

Edited #1

David, Nice work, but for anyone coming late

Keith Newton

I think of a Unicorn as a mythical horse with a single horn coming out of the middle of its forehead. Seems like it might add some clarity to your work for anyone whom hasn't been in of the hundreds of post if you at least added a shot of that to your images. Sorry I'm late to the party.

Re: David, Nice work, but for anyone coming late

#2

It's a spoof name...

David Weaver

..If I said "I want an edge that takes half as long to sharpen, that lasts longer in work, that seems subjectively sharper in paring and takes less effort chopping and makes cheap chisels almost the equal of the best chisels".

You may reply: "Yes, and let us know what you find on your hunt for unicorns this afternoon, too. "

It's simply this:

* grind a primary bevel at 20 degrees

* hone (with a medium stone) a secondary bevel around 3 degrees higher (not precise, just a little higher). No wasting time with wire edges or anything ,just leave the wire edge in place

* buff the chisel briskly in a cotton buff (charged with any reasonable buffing bar) on a buffer for about 5 seconds held about 45 degrees to the buffer wheel and moved about just a little. A light touch of the back of the chisel on the very fluffy outside corner of the wheel will remove any swarf or wax stuck around the back side

That's it. aside from the grind, about 30 seconds. The discussion is of many aspects, but the method is as simple as that. It kind of provides all of the things mentioned above and improves even good chisels.

The reason for the name is because Bill started saying Weaver bevel and things like that make me a little defensive as I'm sure that some aspect of this has been done before. I've been playing at it on and off for years to make it all of the things above and not just another horse.

Re: David, Nice work, but for anyone coming late

#3

Re: It's a spoof name...

William Duffield

I think it's a great name. It should get a lot more traction than even Scary-Sharp™ did when it comes to promotion on the other fora, YouTube, Twitter, InstaGram, etc. You might even want to tack a pseudo ™ symbol onto it.

What is the bevel angle of the tip of a unicorn's horn?

What does a unicorn use to buff it's horn tip? If it uses Cr2O3, might some wag call it a "greenhorn"?

What is the optimum horn tip radius? :D

Re: David, Nice work, but for anyone coming late

#4

The club tshirt

David Weaver

I don't remember if I posted it here or in an email to Bill, but just about the most obscure t-shirt that you could find would be one with a unicorn head on the top and a picture of a buffer on the bottom.

Re: David, Nice work, but for anyone coming late

#5

Re: It's a spoof name...

Paul grover

How about Weaver Beaver Buffing Bevel? 🤔

Re: David, Nice work, but for anyone coming late

#6

Re: It's a spoof name...

David Weaver

I've been called Beaver before. A seemingly elderly (sort of) assistant principal also called me "Mr. Weaner" in honor roll, and I can guarantee there have been worse, too!

Never initiated by me - Always feel better if my name isn't in it!! :|

Re: David, Nice work, but for anyone coming late

#7

Re: It's a spoof name...

Paul grover

Great job, thanks for sharing.

Re: David, Nice work, but for anyone coming late

#8

Re: The club tshirt

William Duffield

Why not put the horn of the Unicorn™ through the center of the buffing wheel?

In allusion to one of your recent comments on another thread, my roommate in college, who had many strange expressions, used to say "a horse of a different feather," As usual, I saw your comment earlier, but can't find it now. Maybe the Unicorn™ should have wings and feathers, like this one:


The open star cluster could be a perfect place for the buffing wheel.

Re: David, Nice work, but for anyone coming late

#9

I voted (elsewhere)

Jim Matthews

For RCH splitter, which gained no traction.

Re: David, Nice work, but for anyone coming late

#10

Re: I voted (elsewhere)

David Weaver

I hope you didn't put that on smc!

Re: David, Nice work, but for anyone coming late

#11

Selling shirts would defray research expenses

Bill Tindall, E.Tn.

:)

The Unicorn must have a shaved patch of hair demonstrating sharpness.

Re: David, Nice work, but for anyone coming late

#12

It was a fanclub...

Jim Matthews

Unmarried, single neckbeards that don't watch Star Trek.

It's on MySpace.

Re: David, Nice work, but for anyone coming late

#13

I divide my time...

Jim Matthews

Between that (my first love) and the one that discovered John Heder has been performing in drag as "Taylor Swift" for nearly a decade.


img

Re: David, Nice work, but for anyone coming late

#14

Re: Selling shirts would defray research expenses

William Duffield

We used to call that patch "Neanderthal Pattern Baldness." You're now going to have to coin another name for the condition. :D

Re: David, Nice work, but for anyone coming late

#15

Re: I divide my time...

David Weaver

Somebody has computer hacking skills!

Re: David, Nice work, but for anyone coming late

#16

I love...

David Weaver

...sayings that just don't quite make sense. Like a horse of a different feather.

Half of one, six dozen of another...

What comes around is all around....

:)

Re: David, Nice work, but for anyone coming late

#17

The tip of the horn

David Weaver

The tip of the horn is going to need to be rounded off a little bit....

Re: David, Nice work, but for anyone coming late

#18

Couldn't resist...

Winston

I just had to make this sketch:


Re: David, Nice work, but for anyone coming late

#19

Re: I love...

William Duffield

Time flies like the wind; fruit flies like a banana. :D