Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Wiley - lapping wooden planes

Posts

Wiley - lapping wooden planes

#1

Wiley - lapping wooden planes

David Weaver

so, I tried this today when I flattened the jack plane.

short history of my lap - works on a part of the bench that is planed extremely flat, 8x42 inch glass shelf 3/8ths thick and flatter on all parts under pressure than a 1.2 thousandth feeler. PSA high quality 80 grit paper to flatten things.

i tracked down a kanna that i modified to use the double iron (the iron itself is a bit looser than a single iron plane and can just barely be pushed to full depth - the subblade then applies the pressure needed to keep the iron in place).

I had prepared this traditionally with a pretty strong hollow, and fully relieved back. It took a while to lap it out (vs. the jack plane, which took a little less than 1 1/2 minutes to lap flat from initial sizing of the blank).

On both, I cannot see any light under the edge of a starrett 380. I believe that off of the lap, they are flat to within a thousandth or so, but I cannot say whether or not I think this is a reasonable standard because I've got a lot of experience with it. Everything is easy once you forget all of the little steps you've taken to get to a certain point.

I lapped the japanese plane with the blade in tension and just out of the reach of the paper and then reset it to depth after that. the 80 grit is important to me for planemaking because things turn out better if each stroke down the lap removes more material - wooden planes are easier to get this flat than softer cast iron planes and those are that much again easier vs. mild steel or really hard cast.

I figured I'd follow up, but this won't be one of my long drawn out "let's see if I can get everyone else to match this", it's a useful skill and inexpensive setup for toolmakers, just as it falls a little short on mild steel and filing the center out and then lapping to finish is useful in that case.

I think there may be some case in this where small surface resonances occur with japanese planes when set traditionally (and thus it's not uncommon for a japanese tool user to true things with a western metal jointer) - the little ripples - if you overwork a certain area, but they shouldn't happen with a lapped plane.

Again, a statement of findings and not an urge for anyone to stray from the traditional method.

Re: Wiley - lapping wooden planes

#2

Re: Wiley - lapping wooden planes

Wiley Horne

Hi David,

Nice set-up!

What was the starting condition of the sole of the jack? Do you check to get your bearings before starting to lap?

Wiley

Re: Wiley - lapping wooden planes

#3

planing everything flat and square...

David Weaver

..any time I make a plane, I've learned that I'd better plane it flat and square to start and very near finished dimension, because it affects layout to some extent, but I really won't do it at the end if I don't do it at the beginning.

So I plane the whole billet flat and square to middling tolerances from the start. It's not flat enough for the plane to work well - in a very fine cut, the plane will skip in and out of a cut, but it's close enough that the coarse paper will do the rest of the work in something like 50 strokes.

There's danger in taking a very twisted plane or one that's got a lot more trouble to get rid of without planing off the "bad" bits first.

getting a picture of a sole with backlighting and a tilted straight edge is a real three handed operation, and this is with two (thus the clamp holding the plane). As this plane is completed, this goofiness is what I'd call my favorite criminal charge when you read the paper -"risking a catastrophe!"

I've tilted a non-taper starrett 380 toward the camera as it's easy to stop light if you let the fat side sit on something.

I figured if I said that I lap things flat, I ought to prove it (otherwise it can just come off as being oppositional for no reason ....not looking to do that).

The glow in the background is the lights on the ceiling. A richer man would have a test light on the bench to put behind the plane.

https://i.imgur.com/mLc3gQI.jpg

The lap (if a single piece of loose grit gets under this glass on one end, it's enough to allow slipping of a feeler under the straight edge once you push down on the center):

https://i.imgur.com/vThIWhG.jpg

The aforementioned japanese plane touched up on a washita after lapping (there just isn't quite enough sharpness to get a cherry shaving of that thickness to hold together)

https://i.imgur.com/1tta2yD.jpg

https://i.imgur.com/mlS4S0P.jpg

It is still pretty fine work, though, and the edge of the cherry board shows the reflection of the garage windows and flowers outside on the surface - it's exceptionally hard to trick the phone autofocus into capturing a glare like this. at least my phone. It instantly flattens the glare and focuses on the bakcground).

https://i.imgur.com/7CASeIf.jpg

All in all, this is a very workable method for keeping a plane in shape, but that's as far as I'd go with it. it's workable. Is it necessary? for me making planes (And constantly flattening vintage irons to get them set up to work in a plane like the jack plane, and do it very quickly) - i'd say yes. Anyone else?

It's doable and not hard, and with the paper setup (coarse high quality high-adhesive power roll) it's one of those things that you find uses for. It's even very good for freehand miter tuning, but it wouldn't need to be nearly so flat for that).

Re: Wiley - lapping wooden planes

#4

Re: planing everything flat and square...

Wiley Horne

David,

Pictures are great, but you never have to ‘prove’ anything to me.

I was asking, because I always check for convexity anywhere, or twist. before lapping, because I’m not able to reliably lap convexity away, and certainly not twist. But you answered this concern by already having planed your billet square and true to begin with.

Thanks for showing!

Wiley

Re: Wiley - lapping wooden planes

#5

Re: planing everything flat and square...

Warren in Lancaster, PA

I have used winding sticks, a straightedge and a smoothing plane for this work for 45 years.

Re: Wiley - lapping wooden planes

#6

I'm sure many have..

David Weaver

if you made 100 or so planes and flattened their irons, refurbished their cap irons and flattened them all (metal and wood), you'd probably do this instead.