Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Desk is glued

Posts

Desk is glued

#1

Desk is glued

Bill Tindall, E.Tn.


I like to assemble a case piece all at once. This one was complicated- 60 joints.

An aid are the dovetailed drawer dividers, an alternative to M&T more commonly employed. When these joints are well made they are self squaring and require no clamping to hold them in place. The strategy is to dry fit enough to hold the piece in alignment, glue in the rest, then glue those that were dry fit. This attribute was a great help in enabling this thing to be assembled all at once. The clamps are used to hold the M&T joints together as needed or in anticipation of maybe needed.

Dry fitting the whole of it enabled a plan to be made and the glue up went smoothly. Some light sanding of scuff marks here and there and this part is ready to be finished.

On to the tedium of yet more drawers. This desk is for a particular application. I'm making it reversible so that at some time in its future the drawers could be used to the left. Never made a reversible drawer before. We will see how that goes.

Re: Desk is glued

#2

Nice 'desk on desk'

Raymond in Trenton NJ

That's looking nice Bill. Good rail at the bottom of the legs, I like that it's at the height of the bottom of the drawers. Good luck with those drawers, no envy here :) Since they will be two-way, will you use anything help keep them centered (not pushing in too far)? A detent/ball catch, something better or nothing?

Curious, decided not to go with a rail at the bottom of the sides? (Thinking here) It's probably a good idea to glue up this way. You'll have enough time to look at it when drawer making. I can't tell (yet), those two clamps on the right are *just* in the right spot :D

Thanks for sharing,

Raymond

Re: Desk is glued

#3

answers

Bill Tindall, E.Tn.

Bottom rail goes on later. It just slips over the bottom panel with a dado, snugly between the legs.

Have not figured out the drawer stop yet. Leaning to do a stop like I always do except screw it on the divider so it can be taken off and moved to the other side if need be.

Re: Desk is glued

#4

Tidy

Jim Matthews

Tidy, neat work.

Kudos

Re: Desk is glued

#5

A comment on the side panels

Bill Tindall, E.Tn.

The horizontal book matched panels are not the result of inspirational design creativity(see discussion on main board). I had some, as it turned out greatly flawed, notion that this construction would be easier than a panel normally encountered in this kind of desk. A panel normally found in this kind of desk should have been a clue that normal usually means most easily done. >(

The result is acceptable. I'm still getting used to the look of it. I've got some nice drawer fronts to go with this case.

Re: Desk is glued

#6

Grain orientation

Jim Matthews

Will drawer grain follow the same direction?

That could be sharp.

Re: Desk is glued

#7

Re: Side Panels - An Idea for You

Hank Knight

Bill, I've built several pieces with solid wood "slat" panels (for lack of a better term) that turned out well. I beaded the edges of the slats to disguise the joint and splined them together to keep them flat. I like the look and it's a pretty easy process. Here are some photos.

[url=https://flic.kr/p/2jcqJtg][/url][url=https://flic.kr/p/2jcqJtg]E8711DB8-CC1D-4813-A5B7-6EC1BAA84CB9[/url] by [url=https://www.flickr.com/photos/158680038@N03/]Hank Knight[/url], on Flickr

[url=https://flic.kr/p/2jcqpG3][/url][url=https://flic.kr/p/2jcqpG3]66DA8476-B290-403E-B68D-6CF4E00DCBAD[/url] by [url=https://www.flickr.com/photos/158680038@N03/]Hank Knight[/url], on Flickr

[url=https://flic.kr/p/21GYb4S][/url][url=https://flic.kr/p/21GYb4S]IMG_0179[/url] by [url=https://www.flickr.com/photos/158680038@N03/]Hank Knight[/url], on Flickr

Re: Desk is glued

#8

Wood movement

Bill Tindall, E.Tn.

If I understand the construction a large flat grain panel seems to be locked against a long grain led. The panel is going to change in height(width) with humidity changes while the leg is going to remain the same length. I think I am not understanding something about this construction that makes it work.

Re: Desk is glued

#9

Seasonal allowances

Jim Matthews

Would the panels "float" with some space to capture expansion?

I'm accustomed to seeing beadboard with overlapping joints to handle movement, as coastal communities see big humidity swings, twice each year.

I like the look of horizontal panels - it's a viable, modern alternative to plywood.

Re: Desk is glued

#10

Mine do

Bill Tindall, E.Tn.

My panels have 2 mm gaps between them. The hard part of this construction was getting them uniform so they looked part of the design and not poor construction.

Board and bead porch ceilings are T&G and not installed tight.

It was not clear what Hank did to allow movement, hence, the question.

Re: Desk is glued

#11

Re: Side Panels - An Idea for You

Wiley Horne

Hi Bill and all,

Hank was suggesting the aesthetic treatment of beading and splining the intersection of the slats. It seems clear at a glance that Hank’s joined panels can float in the framing—on all sides. Or be spot glued on one end.

The bead/spline treatment was his contribution. However he handled the cross grain issue does not detract from the idea, since the panel could be floated.

Wiley

Re: Desk is glued

#13

Re: Wood movement

Hank Knight

Bill and others, yes, the individual horizontal element's (except for the top and bottom and the center elements in the tall panel) float. The top, bottom and center element are tenoned and glued into mortises in the vertical style. The other horizontal elements have shallow stub tenons on the ends that are captured in a groove in the style and float. They are dimensioned to allow space for expansion and contraction and are splined together lengthwise (no glue) to keep the assembly flat. The bead hides the resulting gaps and gives the completed panel the appearance of being solid, with no gaps

Here is a photograph of the bottom horizontal slat in the tall panel that shows the long tenon and the stub tenon. The top and the center slats are similarly formed. The other horizontal slats have only stub tenons that float. The slats in the small panels in the other pictured piece in my original post fit into a frame, so they have only stub tenons that float in grooves in the frame's styles.

[url=https://flic.kr/p/27FRf8a][/url][url=https://flic.kr/p/27FRf8a]IMG_1295[/url] by [url=https://www.flickr.com/photos/158680038@N03/]Hank Knight[/url], on Flickr

Re: Desk is glued

#14

New panel possibilities

Bill Tindall, E.Tn.

Never considered assembling a solid panel with the appearance of an edge profiled board appearance. All the possibilities are fair game- board and bead, vee groove, bull nose, etc. Will file away this idea for a future need. It would be a dandy way to make back panels for case work, for example. Way easier than the frame and panel assemblies I have been making.