Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ash desk

Posts

ash desk

#1

ash desk

Bill Tindall, E.Tn.




A lot of hand work in this one. 64 M&T , 20 dovetail and 2 bridle joints. I was unsure how this experiment would turn out. Looks good enough for the kitchen... a lot better than a 45 year old oak sewing cabinet pressed into service for a kitchen desk.

Dry fit at this point to prove I can get this puzzle together. I will assemble it for good all at once. The original plan was to assemble sub assemblies but some design lack of fore thoughts make it need to go together in an order that precludes doing sub assemblies.

I think I will add a cross piece at the bottom of the legs for enhanced sturdiness.

I should have designed a horizontal piece at the bottom of the right panel to frame the panels like on the top.

Re: ash desk

#2

Re: ash desk

Raymond in Trenton NJ

That looks great Bill. Good luck with the glue up. Agree with the right side panel. You could add a false (or real m&t) rail at the bottom of the panel to mimic the two at the top. I think that would add some balance.

Looks very good man. Can’t wait to see it with finish.

Thanks,

Raymond

Re: ash desk

#3

furniture with recessed side panels

Bill Tindall, E.Tn.



The first piece I made with a recessed side panel I dovetailed in the top rail into the leg, then M&T the panel and bottom rail into the leg . It was a fitting nightmare and I realized after entirely unnecessary.



In this case the panel is M&T into the leg which supplies all the strength necessary. The top and bottom rails are dadoed and fitted over the edge of the panel, a vastly more simple fitting. Fitting is done by shaving bits at a time off the ends with a shooting board until the false rail slides snugly between the legs.

So to add a rail to the bottom will be trivial, except, it will lower the side by5/8" +/-. This addition will lower the side below the drawer rail in the front. I will make the addiiton, dry fit and see how it looks.

Also I realized the panel sets in to much. The shadow is too pronounced. This too is an easy fix. I'll mow off 1/16" from the outside of the legs. I considered making them this much smaller in the start.

Re: ash desk

#4

How will you approach gluing up?

Jim Matthews

Assembling 64 mortise and tenons was an unmentioned labor of Hercules.

(After untangling the Christmas lights and locating a rattling Chevy body panel.)

Sharp work, there.

Kudos

Re: ash desk

#5

looks good....

David Weaver

glue ups are my least favorable thing in the world, or second to least - maybe third...

OK, i can think of worse things, but they're up there!!

Haven't had great luck with modular glue ups, either, will admit - unless there's one modular part and then everything else is glued up to it at once.

At some point in the future, people will probably be talking about that desk like we talk about chestnut now. Looks good.

Possible to add a mock cross piece on the last panel side? (just gluing a rabbeted cross piece to the last panel?

Re: ash desk

#6

The Plan

Bill Tindall, E.Tn.

liquid hide for lubricating and long working time, all at once, with experienced wife helper, pre-adjusted clamps, chamfered tenon ends to make insertion quick, parts numbered for where they go and their orientation and laid out in order.

With nothing to cause pause we can get this assembly together in 10 min or less, well under the max working time of the glue.

The drawer runners presented a step that would be slow. I have arranged this joinery so that they can be slid into place later.

I assemble a case all at once. All the still loose joints can adjust so that everything wiggles around and comes up square before the glue sets.

Re: ash desk

#7

Re: looks good....

Bill Tindall, E.Tn.

Possible to add a mock cross piece on the last panel side? (just gluing a rabbeted cross piece to the last panel?

yes but it will lower the side below the bottom drawer runner. Will try it and see what looks least unattractive.

Re: ash desk

#8

OH, Happy Day!

Bill Tindall, E.Tn.

I was putting away the full sized drawing I made of the desk side when I noted the drawing had a framing piece across the bottom of the horizontal panels. I looked closely at the dry assembled desk side and the panels stop just the right amount short of the bottom of the front drawer divider. So far it is made exactly correct. I just failed to make the bottom rail that goes under the panels to frame them. Well that is a relief.

The problem of taking forever to make something is sometimes I forget where I am at.

Re: ash desk

#9

Ha!

Raymond in Trenton NJ

"The problem of taking forever to make something is sometimes I forget where I am at."

I use that very same method! Yes, sometime it helps. Mostly though ... well that's another story. Looking forward to seeing the unveiling Bill.

Raymond